I'm currently encountering a challenging issue with MassHunter Acquisition Software that has significantly hindered my workflow. I am hoping to leverage the community's expertise to find an effective resolution.
Switching from MRM to dMRM Settings Error…
Dear Community Member,
I have facing some issue in ELECTRONIC PNEUMATIC CONTROLLER (EPC) of GAS CHROMATOGRPAH (7890B) The EPC Module has not give the Set Flow rate for AIR Flow, as we have give the Set Point of Air 350 ml/min, but the observed flow…
I am looking to set up in line sampling on a GC/FID (6850A, G2630A) with a capillary column. I have found sample valves listed for 6850 series GCs (e.g. G2668A), but the part description specifies it is for G2630B, so I take it that this is incompatible…
Part Number
Description
Link to Ordering (includes photo)
126 1012
J&W DB-1 GC Column, 10 m, 0.05 mm, 0.05 µm, 7 inch cag
126-1012 | Agilent
5182 0717
Cap, screw, blue, PTFE/red silicone septa, 100/pk. Cap size: 12 mm
5182-0717…
After some burner head cleaning, I reassembled my FAAS 240FS and now I can't get the burner head to light. Some details:
I was running some "dirty" samples with the nitrous burner head that plugged up the sample capillary and started to block the…
The MS column exits into vacuum. The FID column exits to atmospheric pressure.
Same carrier gas, column, oven temperature, inlet pressure results in different holdup times. These examples are using the Pressure Flow Calculator available here GC Calculators…
Our Ultivo LC/TQ fails autotune immediately citing a Nozzle Fault. The log suggests the associated voltage is out of optimal range. Funnily enough, the system passes check-tune without any issue! The check-tune report shows the voltage perfectly matching…
I'm trying to install Openlab CDS 2.7 on Windows 10. When running the system preparation tool, everything passes test except the Ports Check -configuration: 'workstation ' and it says FAIL. I tried to run the recheck and repair, but it still fails. Any…
I was experiencing ghost peaks in my water blank shots so I decided to do some maintenance. This included a new S/SL liner and septum, removing the first inch or two of the column, FID disassembly and ultrasonic cleaning of the jet, and reassembly. Now…
The probability of water precipitation is very low if the FID temperatures are high enough, but in times of 5890 the FID could not ignite well when water was present. In principle a FID can be operated without makeup gas, which manufacturers officially…
This Information Applies To: Agilent AriaMx real-time PCR system, AriaMx analysis software
Issue
When a sample name starts with zero, the leading zero disappears from the exported data ( Figure 1 and Figure 2 ).
Background
Removing the leading...
This Information Applies To: Agilent 7890B GC system and 7697A headspace sampler
Issue
The 7697 Headspace Sampler can be configured to communicate directly with the 7890B GC. When this direct communication is configured, the 7697A headspace gets...
This Information Applies To: Agilent GC/MSD systems
Issue:
When performing MS tuning, there is error message "No Emission Current" and tune is aborted.
Steps to Follow
This error normally means that the selected filament is not working. Perform...
This Information Applies To: Agilent OpenLab CDS
Issue
Any desired processing method can be assigned to the current Result Set.
Requirements
A result set available to link the method to.
Correct Privilege (Role Membership) set up for the...
This Information Applies To: Agilent LC and CE Systems compatible with Lab Advisor
Issue:
Firmware is updated or downgraded when new features are added, or to fix some system bugs. It also solves compatibility issues when a new module is added to...
This Information Applies To: Agilent OpenLab CDS
Issue
This article shows how to export a report of peak area and retention time of a sequence in an Excel format.
Prerequisites
To be able to carry out the procedure as described, privileges...
This Information Applies To: Agilent OpenLab CDS
Issue
Reports in OpenLab CDS can be printed or saved manually in Data Analysys, or automatically during reprocessing, or acquisition.
Requirements
The user needs the following Roles and Privileges...
This Information Applies To: Agilent 5975 and 5977 Series GC/MSD systems.
Issue
During tuning, MassHunter prompted the error message: "MSD Fault- RFPA Difficulty", and tune action stopped.
Steps to Follow
Try to reconfigure the GC/MS....
This Information Applies To: Agilent OpenLab CSD 2.5 and above
Issue
The integration optimizer helps find a suitable set of integration events. It allows integration parameters to be tuned via sliders (peak width, slope sensitivity, height reject...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue:
This article explains how to install the Agilent 2100 Expert software and connect a PC to an Agilent 2100 Bioanalyzer system.
Steps to follow:
The latest version of...