If your area is relatively stable but your amount/result is low, you have to have either altered your calibration values, failed to clear a previous calibration, or omitted a dilution factor. Are all results lower by the same factor or is it variable…
7890A GC/5975 MS/E.02.02 SP2
Sequence is stopping constantly with the following log book message: "The run was stopped by the instrument's stop button or stop input. The GC Failed to Start."
Found that exact error in the KBR - " Known Problem Report…
I apologize because this is a very blind question- New IT guy to the company and previous didn't have good documentation on this application.
I have a user who is getting the attached error whenever they try and open Sequence Manager or open Bioconfirm…
New FID Jet!
The latest FID jet is intended for use in 6890/7890/8890/8860/8850/9000 GC models
The legacy jets will not work in the 8890/8850/8860/9000 GC models
The new jet makes installing the column seamless with a conical shape to direct the…
Hello
I am having a hard time trying to figure out how to only display one FID signal on a report from a dual injector GC system in OpenLAB 2.4. The calibration that was run used the dual injector setting, but when we were running test samples we only…
System: The GC is an 8890 with TCD in series of two FIDs in parallel (switched via valve). FID 1 has methanizer while FID 2 doesn't.
Had to put the system on standby for 3 weeks over Christmas so kept carrier flowing through the system with all heated…
This 6890 is code named FIDDY because of its dual Flame Ionization Detectors. The SF FBI donated it to UC Davis Chemistry over 10 yrs ago. It is used to teach Chemistry majors gas chromatography and replaced an old Varian 3800 with a chart recorder!
In detail, you can follow below link to resolve this type of problem.
https://community.agilent.com/technical/gc/w/wiki/7889/troubleshooting-an-fid-not-igniting
Hopefully, problem will solve..
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and platinum shield plate must be installed after performing maintenance, or replacing with new components.
Items Required
Standard...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and shield plate must be removed and inspected during routine maintenance, and when troubleshooting plasma ignition problems. Faults with...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
This procedure tests for an air leak in the sample introduction system, or fault with spray chamber draining, by sealing the end of the torch with a piece...
This Information Applies To: 7700, 7800, 7850, 7900 Agilent ICP-MS instruments
Issue
Error messages related to gas flows can cause the plasma to shut off or disable plasma ignition.
The troubleshooting procedure in this article is applicable for...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Error messages related to water flow or water valve issues can cause the plasma to shut off or disable plasma ignition. While a warning message will still...
This Information Applies To: Agilent Fluorescence Detectors (FLD)
Issue
Sometimes it’s necessary to change FLD EX and EM wavelengths during a run since not all components will excite or emit at the same wavelengths. However, when the wavelength...
This Information Applies To: Agilent Analytical Scale LC Systems
Issue
To troubleshoot high backpressure within an HPLC system, it’s necessary to understand the expected pressure throughout an operating system. The total pressure for an LC is measured...
This Information Applies To: Agilent LC Samplers except dual needle multisamplers
Issue
High pressure in the LC sampler is sometimes due to a clog in the needle seat assembly, the needle, or the sample loop. The needle can pick up sample particulates...
This Information Applies To: All OpenLab CDS ChemStation Edition software-Standalone Workstation
Issue
After launching OpenLab ChemStation Online, the following error is shown: “ChemStation ChemMain has stopped working” . OpenLab ChemStation Online...
This Information Applies To: Agilent AriaMx, Software version 1.8 and later
Issue
The Aria Warm up Feature was introduced with Aria SW/FW 1.8 to reduce baseline drift. The warm-up feature is used to speed up the heating process that would normally...