I'm a new GC/MS user and I have the following error: Inlet: Pressure Pre Shutdown warning after changing the column of a Intuvo 9000 Device. The total flow target of 4mL +/-2mL/min fails and the leak rate doesnt' reach values below 11mL/min. Can anyone…
Hello,
I have inherited a 5975 MSD and when I go to autotune, there are no peaks present and the tune fails. I get alternating errors "Gain and Offset = 0 and peaks are too narrow" or "Tune action stopped: The valid Range for Ent Lens Offset is 0…
It may. I'll review the Report Template Editor Concepts Guide and your post (@wydnaa) and see how this works .As for how we would calculate this manually, I'd just divide the result but the expected value (in our case 0.02 ppm) and multiply this by 100…
I have a GC 6850 with an FID. I'll have to upgrade to Windows 10 soon, because Windows will no longer provide security updates for Windows 7. If I upgrade my computer to Windows 10, is there a ChemStation version that's compatible with the 6850 and Windows…
Hi, I am using a 6890 GC in split mode with an isothermal temperature and no flow ramp and operating in constant pressure mode. Please can you advise how using the setting constant makeup flow for the FID detector is different to constant column and makeup…
Won't start without a "Mating Connector"
I use RS232 to control the pump. The mating connector is not present,
The manual says short pins 4 and 5 and pins 8 and 9 of the IO port.
This results in ramp-up and fail.
What is the correct wiring for…
Hello,
Our 6545 QTOF has been idle for a few weeks. When I checked the computer today, I found that "communication failed" errors had started appearing a few days after the instrument was last put to Standby. I'm not sure what happened as I don't think…
Hi, We observed an error during autotune of QQQ GCMS as "Peak width gain failed", When it was occurred and what is the reason for the repeat error, Autotune was not completed due to " Peak width gain failed".
Please suggest the recommendations and possibility…
Hello Michael,
It's kind of a yes and no answer. Technically, the wavelength calibration will have failed because the strontium wavelength was not found - so you will see this if you check the results. Practically this is unlikely to impact operation…
My manager is wanting me to add pass/fail system suitability assessments to my reports/processing methods. In order to limit my validation work and minimize the number of report templates that I am maintaining, I am trying to keep the report adaptive…
This Information Applies To: Agilent 2100 Bioanalyzer system
Issue
Can I run qPCR samples containing Sybr® Green I on the Bioanalyzer?
Background
Sybr® Green I is an Intercalating Dye commonly used to detect amplification products in real...
This Information Applies To: Agilent 4200, 4150 and 2200 TapeStation.
Issue
Is it possible to analyze single stranded DNA (ssDNA) on the TapeStation? Which kit is the most suitable for analysis of ssDNA?
Resolution
Agilent does not offer any...
This Information Applies To: Agilent 4200 and 4150 TapeStation systems
Issue
How to Run the software installation verification on 4200 and 4150 TapeStation systems.
Background
The 4150 TapeStation model G2992A and 4200 TapeStation model G2991B...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, and Femto Pulse
Issue
Perform a capillary alignment when a new array is installed in your Agilent Parallel Capillary Electrophoresis instrument. An alignment may also be performed...
This Information Applies To: Agilent 4200 and 4150 TapeStation
Issue
Are the Agilent DNA and RNA ScreenTape assays denaturing?
Resolution
The DNA ScreenTape assays in the TapeStation portfolio are not denaturing. Only the RNA and High Sensitivity...
This Information Applies To: Agilent LC pumps with manual purge valve.
Issue
A good practice before using a system is to purge the system to remove air. This is done by observing the clear tubing from the solvent bottle as well as the waste line...
This Information Applies To: ICP-MS MassHunter 4.x and 5.x
Issue
Unable to open a batch in offline data analysis, or the batch is empty.
If the ICP-MS MassHunter software closes unexpectedly, there is a power outage, or the ICP-MS and computer...
This Information Applies To: Agilent OpenLab CDS versions 2.4 or higher.
Issue
How to preview result files using various Report Templates in OpenLab CDS versions 2.4 or higher.
Requirements
The user has the result set loaded in OpenLab CDS...
This Information Applies To: ICP-MS MassHunter with Spectroscopy Database Administrator (SDA) and Protect Local Data ON.
Issue
An 'Authentication failed' error message appeared after entering user name and password when attempting to download a...
This Information Applies To: ICP-MS MassHunter with Spectroscopy Database Administrator (SDA) and Protect Local Data On.
Issue
With Spectroscopy Database Administrator (SDA) and Protect Local Data turned on, batches are not accessible through file...