Thanks for the answer but I still fail to understand.
If helium pressure at the inlet of the TD is constant and only controlled manually, why can't it be controlled by the AUX EPC?
Can't I just connect one of the outlet of the AUX EPC through a t…
We fail to properly communicate with the turbo V70 controller, model 969-9507, using RS232.
The communication is ok for all commands that do not answer with more than two bytes, like start and stop.
However, commands supposed to answer with more than…
This document contains a list of FAQ and troubleshooting links for Agilent Cell Analysis products. See also Collection of Cell Analysis Resources .
FAQs
Seahorse:
Agilent Seahorse XF Imaging and Normalization FAQs
Agilent Seahorse XF Real…
Hi community
we getting error message (Configuration system failed to initialize. Chemstation will shutdown now) when we trying to launch Chemstation ,we try rename conf. files in C:\Chem32\1 but that not work.
I appreciated any help .
Dheya
Hi Everyone
This is my first post here in this community. And I really hope to get some ideas to fix my problem, since i'm getting slowly desperate!
So here's my problem: We have some really bad contamination/peaks on all our polar Systems:
I…
Hi,
I get this Front Inlet: Septum purge Pre shutdown warning with Error code: 20401202 with cause showing EPC module is going into a shutdown. This warning showed up immediately after the maintenance was performed to change the septum and SSL liner…
We have a GC-MS instrument and it works well. Recently we installed a new column which connected to FID detector. Now we want to run a method with GC-FID/MS. However, we observed the peaks only in MS spectrum without FID spectrum. We need help with the…
Hi JF_Fortin ,
As andyg mentions, starting with Qual B.08.00 SP1 and Version 10.0 the handling of data files with only 2D detector data has been improved to automatically open non-MS chromatograms.
In previous versions the message you are seeing is…
This file contains a list of 59 commonly used consumables and parts for 7890 GC .
Upload this file to your Smart Alerts software to automatically add these parts to the Master Parts List
This Information Applies To: Agilent 6820, 6890, 7820A GC systems with a Split/Splitless (SSL) inlet
Issue
Non-volatile sample matrix components will accumulate in the inlet liner and impact on analytical performance. The inlet liner should be changed...
This Information Applies To: Agilent headspace samplers (HS)
Issue
GC cycle time needs to be calculated correctly. Too short a GC cycle time will reduce sample quality and possibly stop the analysis prematurely. Too long GC cycle time can cause...
This Information Applies To: Agilent 7820A GC
Issue
7820A GC is designed with simplified keypad that comes with five buttons. They are Stop, Prep Run , Start, Up and Down arrow buttons. Changing the IP address requires a different method compared...
This Information Applies To: Agilent Single Needle Autosamplers
Background
Sometimes the user may observe liquid flowing from Port four on the autosampler injection valve. During an injection sequence, it is normal to have liquid from port four...
This Information Applies To: Agilent 4200, 4150, 2200 TapeStation systems
Issue
Can I run an assay using the ladder or sample buffer from a different assay if I have run out of the appropriate assay ladder or sample buffer? Is it possible to run...
This Information Applies To: Agilent ICP-MS 7700, 7800, 7850, 7900, 8800, and 8900 systems
Issue
Peristaltic pump tubing that has lost its elasticity will not deliver the sample to the nebulizer correctly. When the pump tubing appears limp or flattened...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
AriaMx touch screen displays error code 90 after the Instrument Health Check (IHC), which happens when the AriaMx is switched on, or after running the onboard diagnostic tests...
This Information Applies To: Agilent AriaMx real-time PCR system, AriaMx optical modules
Issue
AriaMx users can change which AriaMx optical modules are installed to upgrade the instrument capabilities or to troubleshoot.
Items Required
Any...
This Information Applies To: AriaMx real-time PCR system
Issue
Error 43 is displayed on the AriaMx touch screen. Error 43 is a voltage error and it normally indicates that the cartridge LED voltage or motor voltage being detected is abnormal. Sometimes...
This Information Applies To: Agilent 2100 Bioanalyzer system
Issue
Can I run qPCR samples containing Sybr® Green I on the Bioanalyzer?
Background
Sybr® Green I is an Intercalating Dye commonly used to detect amplification products in real...