I have just received the Agilent Cary 60 UV-Vis photospectrometer and while following the steps to install the software i receive and error pop up which says "failed to register Class not registered" this occurs no matter what software i try apart from…
Hi everyone,
I've an issue with the fragment analyser (5200) my migration is aborted because the µA target is not achieved (4 instead of 5-1500µA).
The error log is called "HV supply" and I've notice that the little light "HV ON" is not turned on…
Thank you for your help! I will definitely keep in mind. Where is the small and large cover? I will look for the switch breaker at the back. I think it might be the Ar problem, during the 2 to 3 ignitions, the pressure meter on the Ar cylinder dropped…
Working with MassHunter 4.6 Workstation Software for 7900 ICP-MS, G7201C, version C.01.06, Build 621.2
I have a first order calibration with no evidence of any issues (%RE are small and random), but the end client has asked for a 1/x weighting to be…
Hello, I've been using an infinity 1260 autosampler and sporadically during injection I get the error: "Sampler G1329B:DEAAC21082 - Valve to bypass failed [EE 4014, 0]. This causes the system to disconnect and terminate the run. I can restart the entire…
Hi,
When self test on DAD G7117C with 10mm MaxLight Flowcell is performed, it fails because of the spectral flatness (measured 3.3587 AU and limit is 0.002 AU).
Whats exactly calculated in spectral flatness? What could be a reason that this test fails…
We want to connect the output of one column to a splitter and then connect the outputs of the splitter to an MSD and a FID. Is that possible? The MSD worksin vacuum and FID toatmospheric pressure, then the effluent will be sucked by the MSD and there…
Hello what9000 ,
I have a couple questions to try to understand this better:
- What is the outlet voltage?
- Is it a dedicated circuit?
- Are you using any UPS systems, or is the system plugged into the wall directly?
This Information Applies To: Agilent 6820, 6890, 7820A GC systems with a Split/Splitless (SSL) inlet
Issue
Non-volatile sample matrix components will accumulate in the inlet liner and impact on analytical performance. The inlet liner should be changed...
This Information Applies To: Agilent headspace samplers (HS)
Issue
GC cycle time needs to be calculated correctly. Too short a GC cycle time will reduce sample quality and possibly stop the analysis prematurely. Too long GC cycle time can cause...
This Information Applies To: Agilent 7820A GC
Issue
7820A GC is designed with simplified keypad that comes with five buttons. They are Stop, Prep Run , Start, Up and Down arrow buttons. Changing the IP address requires a different method compared...
This Information Applies To: Agilent Single Needle Autosamplers
Background
Sometimes the user may observe liquid flowing from Port four on the autosampler injection valve. During an injection sequence, it is normal to have liquid from port four...
This Information Applies To: Agilent 4200, 4150, 2200 TapeStation systems
Issue
Can I run an assay using the ladder or sample buffer from a different assay if I have run out of the appropriate assay ladder or sample buffer? Is it possible to run...
This Information Applies To: Agilent ICP-MS 7700, 7800, 7850, 7900, 8800, and 8900 systems
Issue
Peristaltic pump tubing that has lost its elasticity will not deliver the sample to the nebulizer correctly. When the pump tubing appears limp or flattened...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
AriaMx touch screen displays error code 90 after the Instrument Health Check (IHC), which happens when the AriaMx is switched on, or after running the onboard diagnostic tests...
This Information Applies To: Agilent AriaMx real-time PCR system, AriaMx optical modules
Issue
AriaMx users can change which AriaMx optical modules are installed to upgrade the instrument capabilities or to troubleshoot.
Items Required
Any...
This Information Applies To: AriaMx real-time PCR system
Issue
Error 43 is displayed on the AriaMx touch screen. Error 43 is a voltage error and it normally indicates that the cartridge LED voltage or motor voltage being detected is abnormal. Sometimes...
This Information Applies To: Agilent 2100 Bioanalyzer system
Issue
Can I run qPCR samples containing Sybr® Green I on the Bioanalyzer?
Background
Sybr® Green I is an Intercalating Dye commonly used to detect amplification products in real...