Hello, i get unusual high signal on FID on 7890 and this message
"Front detector - Fault high voltage error"
What is happening? There is some part I can try to replace before call a technician?
Thank you
I am having a similar issue. First, I replaced a needle seat and then the auto-referencing failed because I failed to recognize that the black sample holders needed to be removed. The needle mechanism seemed forever stuck in the parked position. I was…
Dear colleagues, I keep experiencing the same issue with not being able to open some batches in MH quant (5.1, G7201D / Version D.01.01 / Build 653.5), while others work just fine. I have integrated three batches that were all analyzed, and chromatograms…
Hi,
you should set your instrument to "user tune" in startup. But plasma correction is intended for a regualr setup. you can try to run it with your "special configuration".
Under "Startup Configuration" change the Ignition Sequence to "user tune…
Hi GeorgiaDean were you able to solve your problem?
In regards to the FID not lighting, be sure to refer to the Troubleshooting an FID not igniting article in the Knowledge Portal.
I updated to newer version of Masshunter 10 & when I tried to re establish communication in Lab Advisor, It shows the 1260 HPLC components but Could not connect to QQQ . No connection could be made because the target machine actively refused it 192.168…
Hello, I have initialization problems with my software, MassHunter Workstation software, LC/MS Data Acquisition for 6400 series triple quadrupole Version B.08.00, a service engineer from the brand representative recommended that I uninstall the software…
The struggles continue...
I've been having trouble with my 240fs, and I've arrived at a new problem state. The igniter lights just fine, and the burner head lights, but when I let go of the igniter button the igniter flame goes out immediately and then…
This Information Applies To: Agilent 6820, 6890, 7820A GC systems with a Split/Splitless (SSL) inlet
Issue
Non-volatile sample matrix components will accumulate in the inlet liner and impact on analytical performance. The inlet liner should be changed...
This Information Applies To: Agilent headspace samplers (HS)
Issue
GC cycle time needs to be calculated correctly. Too short a GC cycle time will reduce sample quality and possibly stop the analysis prematurely. Too long GC cycle time can cause...
This Information Applies To: Agilent 7820A GC
Issue
7820A GC is designed with simplified keypad that comes with five buttons. They are Stop, Prep Run , Start, Up and Down arrow buttons. Changing the IP address requires a different method compared...
This Information Applies To: Agilent Single Needle Autosamplers
Background
Sometimes the user may observe liquid flowing from Port four on the autosampler injection valve. During an injection sequence, it is normal to have liquid from port four...
This Information Applies To: Agilent 4200, 4150, 2200 TapeStation systems
Issue
Can I run an assay using the ladder or sample buffer from a different assay if I have run out of the appropriate assay ladder or sample buffer? Is it possible to run...
This Information Applies To: Agilent ICP-MS 7700, 7800, 7850, 7900, 8800, and 8900 systems
Issue
Peristaltic pump tubing that has lost its elasticity will not deliver the sample to the nebulizer correctly. When the pump tubing appears limp or flattened...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
AriaMx touch screen displays error code 90 after the Instrument Health Check (IHC), which happens when the AriaMx is switched on, or after running the onboard diagnostic tests...
This Information Applies To: Agilent AriaMx real-time PCR system, AriaMx optical modules
Issue
AriaMx users can change which AriaMx optical modules are installed to upgrade the instrument capabilities or to troubleshoot.
Items Required
Any...
This Information Applies To: AriaMx real-time PCR system
Issue
Error 43 is displayed on the AriaMx touch screen. Error 43 is a voltage error and it normally indicates that the cartridge LED voltage or motor voltage being detected is abnormal. Sometimes...
This Information Applies To: Agilent 2100 Bioanalyzer system
Issue
Can I run qPCR samples containing Sybr® Green I on the Bioanalyzer?
Background
Sybr® Green I is an Intercalating Dye commonly used to detect amplification products in real...