The file is a pre-set qPCR program to run a plate filled with water used to test the basic raw fluorescence signal of AriaMx Optical modules.
File required for Performing a Background Calibration
The GC cycle time should be the time from injection until the GC is ready to run again. This includes the analysis run, cool down, and equilibration. Based on the times you listed, it would be roughly 40 minutes. It may be worth timing to make sure. The…
Hi howard_sanford, my apologies for a slow response, but thank you very much for the help and advice. I was able to get the filter for Cal and CC to work, and I appreciate the discussion of my larger problem. I think I'm probably several (many) steps…
Hello, thank you for your help. I had tried loading different processing methods but I didn't realize the results were not linked to any method. It turns out the result files were read-only and could not be linked to any method. I moved the result files…
The peaks look similar, essentially the same sensitivity. I'd look at the background on your older runs and the background now. It could be that most of the previous background was one, two, a few, ions and they're gone now. Was that small but still noticeable…
That is one failure mode of Platinum Resistance Thermometers. It can happen one degree to the next higher degree. The heater/sensor must be replaced, part number G1099-60107.
See also: (+) AUX 2 heater fault - Forum - GC/MS - Agilent Community
This Information Applies To: Agilent 5100, 5110, 5800, and 5900 ICP-OES systems
Issue
When troubleshooting communication issues between Agilent 5000 Series ICP-OES and the instrument controlling computer, it is necessary to know the IP address of...
This Information Applies To: Agilent 5000 series ICP-OES systems
Issue
Poor or high relative standard deviation, or a noisy signal is an indication of poor precision during analysis.
Resolution
There are many potential causes for an instrument...
This Information Applies To: Agilent 5000 series ICP-OES systems
Issue
Instrument calibration (wavelength), detector calibration (dark current, or method calibration (worksheet) failure.
Resolution
There are several reasons why a calibration...
This Information Applies To: Agilent 5000 series ICP-OES
Issue
Exhaust temperature and requirements for laboratory site preparation
Background
Certain parameters will impact the actual temperature of the plasma exhaust. Some of these factors...
This Information Applies To: Agilent 700 Series ICP-OES instruments
Issue:
It is important that a torch alignment is performed to ensure that the optics are optimized and are focused on the analytical zone of the plasma. This alignment procedure...
This Information Applies To: Agilent 5800/5900 ICP-OES
Issue:
The instrument requires clean, dry, noncorrosive air for cooling purposes. The air enters the instrument through an air supply vent located beside the chimney on the top of the instrument...
This Information Applies To: Agilent 5100, 5110, 5800, 5900 ICP-OES systems
Issue
The ICP-OES spray chamber filters the sample droplets created by the nebulizer. Larger droplets fall to the chamber drain, while the smaller droplets are introduced...
This Information Applies To: Agilent 5000 ICP-OES Series and Agilent ICP Expert Software
Issue
How to connect Agilent 5000 series ICP-OES systems to Agilent ICP Expert software via LAN
Steps to Follow
How to connect Agilent 5000 series ICP...
This Information Applies To: 5000 series ICP-OES (5100/5110/5800/5900), ICP Expert
Issue
How to Reset the AVS 6/7 after maintenance or when a red LED is visible
Steps to follow
Tips : Instructions for changing the AVS switching...
This Information Applies To: Agilent 5100, 5110, 5800, 5900 ICP-OES
Issue
The axial pre-optic window needs checking from time to time to ensure it is clean.
If the axial pre-optic window is dirty, it must be cleaned or replaced to ensure adequate...