Hydrogen (H2) is the simplest and most abundant element in the universe. Since, it only occurs naturally on Earth when combined with other elements it must be produced from other sources. It can be produced without a carbon footprint from variety of sources…
James, Thanks again. Actually, at first we had "EPC or detector error” and we tried to clean the detector but with no change. Once the GC says “Ignite, ignite” the error pops out. We tried second module (the refurbished) and at first we were receiving…
Hello !
I interesting gc8890 and gc7890.
In datasheet the gc 7890 writing about posible instal 3 detector maximum, but in datasheet gc 8890 writing about posible 4 detector. I never see 4 detectors are installed simultaneously on one chromatograph…
Hi abtisam, The main reason for this problem you didn't select detector signals. when we don't selecAdd t signal detector we never see baseline chromatogram,to solve this problem from online plot for FID signal Click on change than from Edit signal plot…
Hello,
We just recently got a new tapestation 4150 in our lab, which we're trying to set up. As a part of the setup I rand the full system diagnostics to see if the system is working with the Tapestation Test Tape. Everything runs successfully and the…
Hi wcody, thank you for the reply! It is Windows 10 Pro 64-bit. These 6890 FIDs are new to the lab, Windows 10 pro was what the technicians had installed on the computers when we received them.
There is currently no available solution for working with MassHunter data. If your GC has an FID in addition to a mass spec, you could use OpenLab GC ChemStation to acquire the FID signal data. Then addon G2887BA could be used to analyze the ChemStation…
What are the pros and cons of putting a TCD in series with an MS? I know that it's possible to put a TCD and FID in series but I want MS data, not FID data. I tried teeing off the column between the MS and TCD but all the samples keep going to the MS…
ISH, that is a very good question. Yes, you can. However, you have to be mindful of a few things. For the Deans Switch to operate optimally, the downstream pressure need to be the same on both columns downstream of the Deans switch. The MSD operates under…
Problem: Unable to perform Instrument Configuration for Agilent 1290 LC. The instrument pings at IP address 192.168.254.11 with NO packet loss and connects fine in Agilent Lab Advisor software. Able to perform instrument commands in Lab Advisor.
However…
This Information Applies To: Agilent 4200 TapeStation 4150 TapeStation, TapeStation controller software
Issue
The system verification can be run to check the TapeStation performance, for example, when you suspect an instrument hardware fault.
...
This Information Applies To: Agilent 4200 and 4150 TapeStation software.
Issue
How to uninstall and reinstall the 4200 and 4150 TapeStation software.
Background
An uninstallation and reinstallation of the TapeStation software should be performed...
This Information Applies To: 2200 TapeStation instruments, 2200 TapeStation controller software
Issue:
The Agilent 2200 TapeStation controller software won't launch but displays the correct serial number in the top-right corner of the loading screen...
This Information Applies To: 4200, 4150 and 2200 TapeStation, TapeStation analysis software A02.02 or higher.
Issue:
When using the Agilent 4200, 4150 and 2200 TapeStation systems, the DV 200 of FFPE RNA samples can be calculated within the TapeStation...
This Information Applies To: 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, ProSize Data Analysis Software
Issue
How to export a ladder as a size calibration file and import it into a different run in ProSize.
Background
...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software
Issue
It is possible to set up the 2100 Expert software so that the files are automatically exported each time a chip run is complete.
Steps to Follow
To turn...
This Information Applies To: 2100 Bioanalyzer system, 2100 Expert software
Issue:
How to identify and troubleshoot late migration of the ladder, marker, and sample peaks in data generated on the Agilent 2100 Bioanalyzer system.
Background
...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software
Issue
If communication between the 2100 Bioanalyzer and the PC cannot be established, or if an intermittent communication loss occurs, follow the instructions in...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software
Issue
Instructions on how to import from or export data into LIMS software.
Steps to Follow
Data import
When importing sample names and sample comments from...