While removing a column from an Agilent mass spec 5977B the column broke off and I can't figure out how to remove it. I'm using MassHunter version 10.1.64.1 (12/15/2021) but not actually using the mass spec but only the FID on the back. If I start a sequence…
Dear team,
I'm running 8890 GC-FID using back injector and front Detector FID. When, we uploaded sequence table, there's message appearing that sequence table rear injection isn't detected. Can anyone help to advise what to do with that?
Thanks…
How do I convert the Peak Area (pA*s) measurements in a GC-FID lab report into mass/weight percent of components for analysed crude oil samples?
How do I characterise the n-paraffins and estimate the single carbon number (SCN) distribution from the…
I have the flex metal G3188-27501 ferrules. when it comes to the Inlet, the ferrules fit alright and I can tighten them onto the column. When it comes to the FID port, the ferrule is too long and I can't screw in the column to the outlet. If I really…
Hi all :) For he experts here! I did my yearly maintenance (new gold seal, liner, column end cut to inlet and FID, new gas filters, ...). But since then, everytime there's a temperature change in the GC, the signal will show a sudden bump and then it…
I have a chemist who uses GC/MS and has been experiencing issues with running samples and when he connects to the workstation with GC/MS via VNC Viewer it causes the samples to fail and throw errors such as, "Cannon open file D:\MassHunter\GCMS\1\simulate…
Dear Colleagues, apologizing for frequently wondering but I first faced this problem. GC produces a signal without turning on the FID Detector!? Please look at the attached photo. After turning on the detector and then conditioning the column while the…
Hello!
I am inquiring about a Turbo-V 3K-T High Vacuum Turbo Pump which unfortunately failed due to a bearing problem. I would like to receive information and advice on the following issues:
1. Is a repair kit available for the Turbo-V 3K-T pump?…
Recently, we connected the column (CP7429) to TCD and FID using a Y splitter. However, there is no signal response on both TCD and FID after manually injection of the calibration gas (containing H2, CO, CH4, C2H4, C2H6 in CO2). The carrier gas is Ar.…
Hello,
To calculate the RSD and Pass/Fail results, one can try the following:
In the reporting go to the edtor and open "table properties"
In my specific case, I want to calculate RSD for Area, so I choose the column A, pA*s and press "Column…
This Information Applies To: Agilent 4200 TapeStation 4150 TapeStation, TapeStation controller software
Issue
The system verification can be run to check the TapeStation performance, for example, when you suspect an instrument hardware fault.
...
This Information Applies To: Agilent 4200 and 4150 TapeStation software.
Issue
How to uninstall and reinstall the 4200 and 4150 TapeStation software.
Background
An uninstallation and reinstallation of the TapeStation software should be performed...
This Information Applies To: 2200 TapeStation instruments, 2200 TapeStation controller software
Issue:
The Agilent 2200 TapeStation controller software won't launch but displays the correct serial number in the top-right corner of the loading screen...
This Information Applies To: 4200, 4150 and 2200 TapeStation, TapeStation analysis software A02.02 or higher.
Issue:
When using the Agilent 4200, 4150 and 2200 TapeStation systems, the DV 200 of FFPE RNA samples can be calculated within the TapeStation...
This Information Applies To: 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, ProSize Data Analysis Software
Issue
How to export a ladder as a size calibration file and import it into a different run in ProSize.
Background
...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software
Issue
It is possible to set up the 2100 Expert software so that the files are automatically exported each time a chip run is complete.
Steps to Follow
To turn...
This Information Applies To: 2100 Bioanalyzer system, 2100 Expert software
Issue:
How to identify and troubleshoot late migration of the ladder, marker, and sample peaks in data generated on the Agilent 2100 Bioanalyzer system.
Background
...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software
Issue
If communication between the 2100 Bioanalyzer and the PC cannot be established, or if an intermittent communication loss occurs, follow the instructions in...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software
Issue
Instructions on how to import from or export data into LIMS software.
Steps to Follow
Data import
When importing sample names and sample comments from...