In my experience, usually when a method fails to download to a 7820A GC it means that one of the zones on the GC is in a faulted state. This does not always get reported in the instrument actuals in ChemStation, so the best way to double-check this is…
Hello everyone, This is my first post and I'm excited to have discussions for this thread. I wanted to start off with a small introduction with some of my experience. I have 4 years of experience in operation, maintenance, method development on the following…
Hello,
We have a GC 7890A model equipped by tray (SN#CN90452624) and Autosampler (SN#7683) I am receiving the following message while trying to run sample followed by a shaking arm and beeping noise. Any help on what might cause the problem is greatly…
Column: HP-PLOT/Q+PT 30M +5M Duraguard (2.5M on either end) 0.530 mm megabore, 40Micro film Primary components residual EO and PO in various acceptor chemistries. Separate STDs for each, both are showing area decline, on FID, recently switched out flame…
It knows that the electrometer board is plugged into the main board and expects everything else to be there, too. The simplest suggestion is to power down, unplug the GC from the wall, remove the FID electrometer from the main board, button it back up…
Dear Agilent,
I am trying to perform a "backflush scouting run", using the nice backflush wizard option in Chemstation rev. C.01.10, for configuration of a useful backflush time to my GC method. However, the backflush wizard unfortunately stops after…
My GC-FID says the following when I change the split ratio form 50:1 to 200:1: Front inlet flow limited. I dont know what I need to change further so it won't be limited. Does anyone have some tips
Hi chemist85 , I'd like to inform you that our instrument problem was solved, and yes it caused by the broken UPS, the output voltage is dropped to 160 volts when igniting the plasma, and also the voltage was not stable at all and unfortunately, it also…
Good day Agilent, I am really humbled to join the community. I have a few inquiry I would like to make.
I am having a very noisy baseline every time I try to bake out using both ECD and FID,
When I analyze acetaldehyde using the FID it keeps the noise…
Hi.
So ive had a very high sample with Methanol (around 8000 mg/l) and now i still have contamination around 500 mg/l in my blanks. Ive tried injecting IPA and replaced the syringe. Any other tips? Ive also pumped up the oven/column tempature to a…
This Information Applies To: Agilent 4200 TapeStation 4150 TapeStation, TapeStation controller software
Issue
The system verification can be run to check the TapeStation performance, for example, when you suspect an instrument hardware fault.
...
This Information Applies To: Agilent 4200 and 4150 TapeStation software.
Issue
How to uninstall and reinstall the 4200 and 4150 TapeStation software.
Background
An uninstallation and reinstallation of the TapeStation software should be performed...
This Information Applies To: 2200 TapeStation instruments, 2200 TapeStation controller software
Issue:
The Agilent 2200 TapeStation controller software won't launch but displays the correct serial number in the top-right corner of the loading screen...
This Information Applies To: 4200, 4150 and 2200 TapeStation, TapeStation analysis software A02.02 or higher.
Issue:
When using the Agilent 4200, 4150 and 2200 TapeStation systems, the DV 200 of FFPE RNA samples can be calculated within the TapeStation...
This Information Applies To: 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, ProSize Data Analysis Software
Issue
How to export a ladder as a size calibration file and import it into a different run in ProSize.
Background
...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software
Issue
It is possible to set up the 2100 Expert software so that the files are automatically exported each time a chip run is complete.
Steps to Follow
To turn...
This Information Applies To: 2100 Bioanalyzer system, 2100 Expert software
Issue:
How to identify and troubleshoot late migration of the ladder, marker, and sample peaks in data generated on the Agilent 2100 Bioanalyzer system.
Background
...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software
Issue
If communication between the 2100 Bioanalyzer and the PC cannot be established, or if an intermittent communication loss occurs, follow the instructions in...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software
Issue
Instructions on how to import from or export data into LIMS software.
Steps to Follow
Data import
When importing sample names and sample comments from...