The file is a pre-set qPCR program to run a plate filled with water used to test the basic raw fluorescence signal of AriaMx Optical modules.
File required for Performing a Background Calibration
The GC cycle time should be the time from injection until the GC is ready to run again. This includes the analysis run, cool down, and equilibration. Based on the times you listed, it would be roughly 40 minutes. It may be worth timing to make sure. The…
Hi howard_sanford, my apologies for a slow response, but thank you very much for the help and advice. I was able to get the filter for Cal and CC to work, and I appreciate the discussion of my larger problem. I think I'm probably several (many) steps…
Hello, thank you for your help. I had tried loading different processing methods but I didn't realize the results were not linked to any method. It turns out the result files were read-only and could not be linked to any method. I moved the result files…
The peaks look similar, essentially the same sensitivity. I'd look at the background on your older runs and the background now. It could be that most of the previous background was one, two, a few, ions and they're gone now. Was that small but still noticeable…
That is one failure mode of Platinum Resistance Thermometers. It can happen one degree to the next higher degree. The heater/sensor must be replaced, part number G1099-60107.
See also: (+) AUX 2 heater fault - Forum - GC/MS - Agilent Community
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
Before replacing the electrodes and/or shroud, the GTA Furnace workhead will need to be disassembled. After replacing the electrodes and shroud, the GTA Furnace workhead will...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer
Issue
After starting a run, the run is aborted with the following error: Current = 0.0uA, Expected range: 5 - 3000.
Steps to Follow
Check...
This Information Applies To: Agilent OpenLab CDS 2.x in file system configuration
Issue
Sometimes, you will need to change the Projects Root Path / Project Storage Path . This article outlines the procedure on how to change it.
Background
...
This Information Applies To: 5000 series ICP-OES (5100,5110,5800,5900), AVS 4/6/7
Issue
Steps to bypass the AVS to troubleshoot poor performance on the ICP-OES
Tip : These steps should be completed after the Subsystem Communication...
This Information Applies To: Agilent 8890/8860 GC Systems with SSL, MMI, PTV, or VI inlets.
Issue
Split vent trap replacement is recommended as part of the scheduled preventive maintenance. Sometimes, it has to be replaced when the inlet pressure...
This Information Applies To: Agilent 6000 Series LC/MS systems equipped with MS40+ rotary vane pumps
Issue
Instructions on how to replace the filter in an Agilent MS 40+ pump as part of annual pump maintenance
Background
The filter in the...
This Information Applies To: Agilent ICP-OES 5000 Series (5100/5110/5800/5900) with ICP Expert 7.5.x Software
Issue
The Recommended Routine Maintenance Schedule does not adjust for the number of samples analyses or the sample matrix, both of which...
This Information Applies To: Agilent 7890/7820 GC Systems with SSL, MMI, PTV, or VI inlets.
Issue
Split vent trap replacement is recommended as part of the scheduled preventive maintenance. Sometimes, it has to be replaced when the inlet pressure...
This Information Applies To: Agilent LC pumps
Issue:
Stuck or obstructed check valves (Active Inlet Valve (AIV), Passive Inlet Valve (PIV), Outlet Ball Valve (OBV)) can cause issues such as no-flow or no-pressure, moderate to strong drops in pressure...
This Information Applies To: Agilent 1260 Infinity II multisampler, 1290 Infinity II multisampler, 1260 Infinity II SFC multisampler, and 1260 Infinity II bio-Inert multisampler
Issue
The needle bends while moving to the wash port or showing one...