This is a discussion with Rob Dejong, Agilent's Micro GC Product Manager. We discuss hydrogen energy and how the Micro GC can be used to analyze hydrogen fuel blended with natural gas. Hydrogen energy is an exciting topic as it is a big part of the green…
Hi aline.castilla-vitkovsky
Better to create the methods in the 8890 from the default method, (default.m).
If the version of the software are different you may have problems with it.
Thanks
Regards
Support and educational resources for VWorks Automation Control Software for Liquid Handling including VWorks Standard and VWorks Plus (compliance-enabled).
Support Documents
Automation Solutions Help and Learning
Automation Software and Devices…
Hello,
Agilent stopped supporting Galaxie in 2014 so we no longer provide the software. Attached was the note announcing the discontinuation. OpenLan CDS 2.x can support certain versions of the 490 GC. You might also have options with OpenLab EZChrom…
Hi Chelsea!
That column was hidden. I didn't even know there were more columns available there and, sure enough, the "Level 1" was missing. Not sure what happened to it, but that's an easy fix.
Thank you for your help!
Jacob,
I am new to chemstation software and trying to learn it. I am having the same problem using the same method. I am testing hemp. Did you figure out why you were getting incorrect potency? Also, are you using (Multipliers = 20, 20. Dilution factors…
It is less volatile, but should work from your aqueous medium. Incubation temperature 80-90 °C, incubation time 10-20 minutes. With a SPME PDMS fiber (10%) you could even improve it more.
Hi Nadjan, I have some good news . I ordered a drain management kit G4267-68708. I replace the only washport in G7167A, and it successfully completed the autoreferencing. You were right, it is all due to washport, I did not change the whole drain kit…
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
Over time, the electrodes may become pitted or eroded and users may see a decrease in precision or begin to experience the "Tube fault" error when new tubes are installed. If...
This Information Applies To: Agilent GTA Furnace and Flame Instruments, Agilent 240FS/240GFAA/GTA120/PSD120
Issue
There may be occasions when users need to remove GTA furnace center block workhead (instruments with both Flame and Furnace capabilities...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
The shroud should be replaced annually, or when there is evidence of damage caused by mechanical shock or contamination from liquid spillage.
Items Required
Shroud Removal...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
Before replacing the electrodes and/or shroud, the GTA Furnace workhead will need to be disassembled. After replacing the electrodes and shroud, the GTA Furnace workhead will...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer
Issue
After starting a run, the run is aborted with the following error: Current = 0.0uA, Expected range: 5 - 3000.
Steps to Follow
Check...
This Information Applies To: Agilent OpenLab CDS 2.x in file system configuration
Issue
Sometimes, you will need to change the Projects Root Path / Project Storage Path . This article outlines the procedure on how to change it.
Background
...
This Information Applies To: 5000 series ICP-OES (5100,5110,5800,5900), AVS 4/6/7
Issue
Steps to bypass the AVS to troubleshoot poor performance on the ICP-OES
Tip : These steps should be completed after the Subsystem Communication...
This Information Applies To: Agilent 8890/8860 GC Systems with SSL, MMI, PTV, or VI inlets.
Issue
Split vent trap replacement is recommended as part of the scheduled preventive maintenance. Sometimes, it has to be replaced when the inlet pressure...
This Information Applies To: Agilent 6000 Series LC/MS systems equipped with MS40+ rotary vane pumps
Issue
Instructions on how to replace the filter in an Agilent MS 40+ pump as part of annual pump maintenance
Background
The filter in the...
This Information Applies To: Agilent ICP-OES 5000 Series (5100/5110/5800/5900) with ICP Expert 7.5.x Software
Issue
The Recommended Routine Maintenance Schedule does not adjust for the number of samples analyses or the sample matrix, both of which...