Hello, I am looking at flavor compounds on a GC/FID. All of my peaks integrate really well except the aldehydes. There is a slight baseline rise long before the actual peak somes out and the GC begins integration at that time. I've tried changing the…
Thanks! To add, I just ran the software verification tool and the MassHunter GCMSAcq_base.xml report failed. File Report Summary
Missing files or invalid files found:
Invalid Files :1
No system file difference found
Invalid Files …
Hi there! We have a Cary 60. We are doing preventive maintenance, but the noise test fails and it took up to three or four times to get a successful result. What can we do to improve this and get a passed result the first time?
We have several 1220 Infinity II system (G4290B) on our location. They are connected same type of computers with same windows. Only one of them has connection issue as below. Since there is connection to detector (I can control detector fully), I am not…
Hope your week is going well, can wait for spring to actually arrive.
When we turn auto offset on for either of our GCs, it ramps the output so high that it shuts down. This is just for the nitrogen phosphorus detector. We normally turn it off, but…
Hi mubashirraza, PCBs are not commonly sampled via headspace. SPE is more commonly used as a cleanup step followed by standard auto-sampler injection. PCBs are more often detected using MS or uECD due to their more selective operation. I've attached some…
When running a calibration on the GCMS the internal standard increases the entire time for all of our standards. It goes from around 1.9 million for the bottom of the calibration to 3.2 million. Recent things that we have done that should help eliminate…
Hello, we were not able to tune the instrument at all. There was so much noise at low mass that it fails the initial quad coarse mass calibration. We think it is PEG contamination, possibly also PPG, but a number of masses correspond with sodiated PEG…
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, and Oligo Pro II systems
Issue
The volume of sample used by Agilent parallel capillary electrophoresis systems during a run.
Resolution
The...
This Information Applies To: Agilent 2100 Expert software, 2100 Expert Security Pack, 2100 Bioanalyzer
Issue
When opening the 2100 Expert software and using the Security Pack, the error message " Start of launcher application failed - The requested...
This Information Applies To: Agilent 6890, 6850, 7890, 8890, 8860, Intuvo 9000 GC systems.
Issue
The exchange of the ignitor in a Flame Photometric Detector (FPD) may be required in the following scenarios:
Preventive or periodic maintenance...
This Information Applies To: Agilent 1290 Infinity Quaternary Pump G4204A, 1290 Infinity II Flexible Pumps G7104A/C, and G7131A/C.
Issue
If the flexible/quaternary pump does not generate flow or build up pressure, it could be due to a stuck inlet...
This Information Applies To: Agilent 5200, 5300 and 5400 Fragment Analyzer systems
Issue
Separation times for the Fragment Analyzer for each array format and kit.
Resolution
Caution : The times in this article are the length of time...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, Oligo Pro II, ProteoAnalyzer systems
Issue
Guidance for installing the Agilent parallel capillary electrophoresis instrument controller and/or...
This Information Applies To: OpenLab CDS (version 2.x) system
Issue:
This article explains how to export OpenLab CDS 2.x data as Archived file.
For copying OpenLab CDS 2.x data to another Projects or another OpenLab CDS systems, you can use data...