Hi all,
New to the forum, and having a few issues with our analytical 1260 HPLC. Main problem currently is an intermittent error on the auto sampler when trying to inject samples, it doesn’t happen necessarily at the first injection in each sequence…
Which voltage test point? The sideboard is permanently damaged if the cables are connected to it while the power is on. Did that happen?
Notice in your picture above that the HED is set to On.
If the HED power supply is not functioning properly…
Have you checked that your stock standards are not contaminated and tried a second source of SIC. Do you run He in addition to nogas and does it only fail for nogas but pass in He?
I've also seen Sb stick around in the tubing, autosampler probe, and…
Hello, How often does your reference amount for the compounds change? If it never changes or changes on an infrequent basis I would suggest using a constants file in custom calculator. Also we have seen syntax issues with expressions in IR when using…
Agilent 1200 Series Analytical Fraction Collectors_ Continues to FAIL initialization, also error code 3833 and error message needle too long, too short or missing. please Advise
I have the headspace autosampler 7697A attached to a GC 7890A. I have two issues. the first is a growling noise when the gripper moves in the downward motion. Not the entire way just the middle third. I am guessing a service call will need to be made…
Hello,
That will work but what value are you displaying? If you want the logic to be if any injection fail it shows unmet then you would need to store and evaluate the logic. I would have a hidden column that converts met and unmet to 0 and 1. You…
That's interesting. I wonder if there are any differences to be expected between a 6890N and a 7890 GC when using Chemstation on the 6890N and Openlab 2.3 on the 7890 with FID? Also, would there be any differences in the signal to noise and dynamic range…
Hello, Finally we were able to resolve, for some reason the scheduled task that is supposed to generate the certs at startup was failing. Recreating and running the task fixed the certificate after rename issue, and now the client is able to connect to…
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, and Oligo Pro II systems
Issue
The volume of sample used by Agilent parallel capillary electrophoresis systems during a run.
Resolution
The...
This Information Applies To: Agilent 2100 Expert software, 2100 Expert Security Pack, 2100 Bioanalyzer
Issue
When opening the 2100 Expert software and using the Security Pack, the error message " Start of launcher application failed - The requested...
This Information Applies To: Agilent 6890, 6850, 7890, 8890, 8860, Intuvo 9000 GC systems.
Issue
The exchange of the ignitor in a Flame Photometric Detector (FPD) may be required in the following scenarios:
Preventive or periodic maintenance...
This Information Applies To: Agilent 1290 Infinity Quaternary Pump G4204A, 1290 Infinity II Flexible Pumps G7104A/C, and G7131A/C.
Issue
If the flexible/quaternary pump does not generate flow or build up pressure, it could be due to a stuck inlet...
This Information Applies To: Agilent 5200, 5300 and 5400 Fragment Analyzer systems
Issue
Separation times for the Fragment Analyzer for each array format and kit.
Resolution
Caution : The times in this article are the length of time...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, Oligo Pro II, ProteoAnalyzer systems
Issue
Guidance for installing the Agilent parallel capillary electrophoresis instrument controller and/or...
This Information Applies To: OpenLab CDS (version 2.x) system
Issue:
This article explains how to export OpenLab CDS 2.x data as Archived file.
For copying OpenLab CDS 2.x data to another Projects or another OpenLab CDS systems, you can use data...