Hello vtpolywood ,
What type of GC do you have, if I may? If it's an 8890 for example there are some Diagnostic tests built-in that you can run on the Cool On Column inlet. Have you recently changed gas tanks (whether carrier, FID fuel, air or makeup…
In MSD Chemstation, you can specify which signal to use for quantification: TIC, Target Ion, or GC Signal (for GC detectors like FID, TCD, etc.) Go to the Calibrate menu and select Edit
Compounds. On the Compound Table Identification tab, look for the…
Hi,
I plan to attempt some SimDist analysis in accordance with D2887 on my agilent GC-FID. I was hoping that I could achieve this without additional software (i.e. just through manual manipulation of the data acquired by Chemstation), but apparently…
Our micro GC 990 is Natural Gas Analyzer B and B extended version with 3 channels (PoraPLOT U, 6-meter CP Sil 5 CB, CP-Molsieve 5A). We are having trouble with data processing. We have 2 calibration gases from Agilent (Natural Gas mixture and Universal…
ICP-MS MassHunter Version 4.1. I cannot Startup Standard Lens Tune!
The message appears "Failed to add Startup/Hardware tasks to Queue; Enter path for batch folder".
As usual (my Batchs)- everything works.
Hello,
Our Headspace sampler 7697A Leak test failed. Leak test failing at the stage 1 off the Restriction and Pressure Decay Test.
Going from there, the sample probe was replaced as well as the pressurization solenoid valve but without success.
…
Hi everyone.
We have a 8890 Agilent GC with nickel catalyst and FID detector. We would like to use hydrogen as carrier gas, but we don’t know the right flow rates, because the manual is indicating flow rates only for using helium as carrier gas.
For…
Hi!
I still need help yes, please!
- On the machines (GC system and Injector) it just says HP6890 (see photos attached)
- The PC we employ is an old Windows XP running one, that was used to run the GC-FID before we want to control it with the serial…
Hi there, I noticed recently that the ECD back signal on Agilent GC 7890 (using it for trace gas analysis) is oddly spiking (while the FID is a straight, consistent line). It never used to do this. I just recently changed the inlet septum, could this…
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, and Oligo Pro II systems
Issue
The volume of sample used by Agilent parallel capillary electrophoresis systems during a run.
Resolution
The...
This Information Applies To: Agilent 2100 Expert software, 2100 Expert Security Pack, 2100 Bioanalyzer
Issue
When opening the 2100 Expert software and using the Security Pack, the error message " Start of launcher application failed - The requested...
This Information Applies To: Agilent 6890, 6850, 7890, 8890, 8860, Intuvo 9000 GC systems.
Issue
The exchange of the ignitor in a Flame Photometric Detector (FPD) may be required in the following scenarios:
Preventive or periodic maintenance...
This Information Applies To: Agilent 1290 Infinity Quaternary Pump G4204A, 1290 Infinity II Flexible Pumps G7104A/C, and G7131A/C.
Issue
If the flexible/quaternary pump does not generate flow or build up pressure, it could be due to a stuck inlet...
This Information Applies To: Agilent 5200, 5300 and 5400 Fragment Analyzer systems
Issue
Separation times for the Fragment Analyzer for each array format and kit.
Resolution
Caution : The times in this article are the length of time...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, Oligo Pro II, ProteoAnalyzer systems
Issue
Guidance for installing the Agilent parallel capillary electrophoresis instrument controller and/or...
This Information Applies To: OpenLab CDS (version 2.x) system
Issue:
This article explains how to export OpenLab CDS 2.x data as Archived file.
For copying OpenLab CDS 2.x data to another Projects or another OpenLab CDS systems, you can use data...