I have recently ran two standards on the Cary 630 FT-IR using the ATR module - qualitative search. One is Heptanes and the other is N-Heptane.
I then ran four samples - three were N-Heptane, the other was Heptanes and compared them to the two standards…
megaflorch - this was fairly old topic and I wasn't sure if you completed your standards/sample prep. I use a similar technique to get my analytes within a better working linear range with respect to my GC-FID. Your logic is good.... here is my standard…
I went through everything I could find, but it appears that BootP doesn't work properly in Windows 10 and even when you follow the instructions it fails. As I mentioned above, the only way I found to get it working was to replace the JetDirect card with…
I have Chemstation C.01.08 [210]. Whenever I try to run a partial sequence, I get the 'Initialization of Sequence Failed' error message. From what I could find online, that issue was supposed to be solved in C.01.08 version of the software. I have Unique…
I am having trouble separating methyl methacrylate (MMA) from another peak. The interfering compound, appearing in the front, is identified by library as 3,3-dimethyl-2-butanone and it is inherent to the sample. MMA appears as the split/tailing peak.…
You can definitely set up an intelligent report to do what you want, but there is a much easier way to do this in OpenLAB ChemStation. When you create a calibration table, ChemStation gives you an option to 'Calculate Signals Separately': When selected…
Hi,
I am currently running a USP <467> protocol which monitors the recovery of: methanol, ethanol, acetone, isopropyl alcohol, hexanes, and toluene. I make a standard solution using DMAC with known amounts of solvent and use the same solution to spike…
I did a lens ramp on the failed BFB_AT and the emission ramp for 50 amu was very choppy. Setting the emission at 50 amu is where the tune process fails. Could this be due to a hardware problem?
Hi Lakshmi, Here is the reply from our compliance group.... Traceability and Audit Trails Data are generated by the same native chromatography data system (CDS) used in the daily operation of the instrument, which controls the system being qualified during…
Hi,
Every time we vent and vacuum down the MS2 auto tune fails with the high mass.
I've tried to tune from factory settings and manual tune using a file that was used prior to the shutdown.
The instrument is second hand so we have had the vendor…
How to Reset the GC/TQ Tune File to Default Values
Multiple Results
This Information Applies To: Agilent 7000A/B/C/D Triple Quadrupole GC/MS systems
Issue
When a triple quadrupole GC/MS system tune fails, the user can check for any abnormalities by setting the tune file to default tune file before checking for hardware...
This Information Applies To: Agilent ICP-OES 5000 Series (5100/5110/5800/5900)
Issue:
The ICP-OES and AVS 6/7 components require regular routine maintenance. Agilent-authorized field service engineers must perform any maintenance procedures not...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, OligoPro, and ZAG DNA Analyzer
Issue
Perform a capillary alignment whenever a new array has been installed on an Agilent Parallel Capillary Electrophoresis instrument...
This Information Applies To: MSD productivity ChemStation E.XX.XX and F.XX.XX
Issue
A setup method for MSD Productivity ChemStation E.XX.XX and F.XX.XX users who want to stop printing results automatically after sample analysis.
Steps to Follow...
This Information Applies To: Agilent MassHunter 11 and later
Issue
Generating Acquisition Desktop and Quantitative Analysis shortcuts.
Steps to Follow
Double-click the Control Panel icon on the desktop or select Windows Start menu > Agilent...
This Information Applies To: Agilent MassHunter Workstation for LC/TQ and MassHunter Workstation for LC/TOF and LC/Q-TOF
Issue
How to view the MassHunter Data Acquisition Software Logs entries, change settings, and export the Logbook for archiving...
This Information Applies To: ICP-MS MassHunter with User Access Control (UAC)
Issue
It is necessary to update the database folder path in Change User Access Control:
After creating a new database in SDA with ICP-MS MassHunter.
To view a batch...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
Over time, the electrodes may become pitted or eroded and users may see a decrease in precision or begin to experience the "Tube fault" error when new tubes are installed. If...
This Information Applies To: Agilent GTA Furnace and Flame Instruments, Agilent 240FS/240GFAA/GTA120/PSD120
Issue
There may be occasions when users need to remove GTA furnace center block workhead (instruments with both Flame and Furnace capabilities...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
The shroud should be replaced annually, or when there is evidence of damage caused by mechanical shock or contamination from liquid spillage.
Items Required
Shroud Removal...