When running a calibration on the GCMS the internal standard increases the entire time for all of our standards. It goes from around 1.9 million for the bottom of the calibration to 3.2 million. Recent things that we have done that should help eliminate…
Hello, we were not able to tune the instrument at all. There was so much noise at low mass that it fails the initial quad coarse mass calibration. We think it is PEG contamination, possibly also PPG, but a number of masses correspond with sodiated PEG…
The tune evaluation criteria are benchmarks that GCMS instruments typically pass.
"Designed for" and "works with" are two different things. The tune evaluation was created before the Extractor Source and High Efficiency Source. These ion sources get…
Hey Ryan, try the following. Normally, the valve command failed is coming as a result of the position not found. Overtightened screws are a typical result if you have done maintenance before (happened to me the first time...). Tighten the screws each…
Morning, You are correct. I am running OpenLab CDS ChemStation. Rev code = C.01.04 [35]. Intelligent Reporting product version A.01.04.122. The system suitability issue is that I'm only getting the TCD satistical results. The FID result are not printing…
Hello Lars, Thanks for your reply. Unfortunately, there is no flow meter meter installed. So you are saying that, in your case without stopping gas flow before GC injection, you are only getting 1-2% deviation in FID response? If possible could you explain…
I have a G4226A autosampler with a recurring error message. Movement of needle into seat failed [EE 4714, 3204]
This error started after the autosampler had been repaired by a field engineer. The main board had to be replaced; the computer was unable…
I think that, with this version of the software, there are configuration files stored in the "instrument number folder", e.g. C:\Chem32\n I was going to suggest that you try to delete/rename the config.reg file, having closed all instances of Chemstation…
This Information Applies To: Agilent MassHunter 11 and later
Issue
Generating Acquisition Desktop and Quantitative Analysis shortcuts.
Steps to Follow
Double-click the Control Panel icon on the desktop or select Windows Start menu > Agilent...
This Information Applies To: Agilent MassHunter Workstation for LC/TQ and MassHunter Workstation for LC/TOF and LC/Q-TOF
Issue
How to view the MassHunter Data Acquisition Software Logs entries, change settings, and export the Logbook for archiving...
This Information Applies To: ICP-MS MassHunter with User Access Control (UAC)
Issue
It is necessary to update the database folder path in Change User Access Control:
After creating a new database in SDA with ICP-MS MassHunter.
To view a batch...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
Over time, the electrodes may become pitted or eroded and users may see a decrease in precision or begin to experience the "Tube fault" error when new tubes are installed. If...
This Information Applies To: Agilent GTA Furnace and Flame Instruments, Agilent 240FS/240GFAA/GTA120/PSD120
Issue
There may be occasions when users need to remove GTA furnace center block workhead (instruments with both Flame and Furnace capabilities...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
The shroud should be replaced annually, or when there is evidence of damage caused by mechanical shock or contamination from liquid spillage.
Items Required
Shroud Removal...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
Before replacing the electrodes and/or shroud, the GTA Furnace workhead will need to be disassembled. After replacing the electrodes and shroud, the GTA Furnace workhead will...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer
Issue
After starting a run, the run is aborted with the following error: Current = 0.0uA, Expected range: 5 - 3000.
Steps to Follow
Check...
This Information Applies To: Agilent OpenLab CDS 2.x in file system configuration
Issue
Sometimes, you will need to change the Projects Root Path / Project Storage Path . This article outlines the procedure on how to change it.
Background
...
This Information Applies To: 5000 series ICP-OES (5100,5110,5800,5900), AVS 4/6/7
Issue
Steps to bypass the AVS to troubleshoot poor performance on the ICP-OES
Tip : These steps should be completed after the Subsystem Communication...