Good Morning, Just setup a 7890B GC with Empower 3 for the CDS Built an instrument method to use both the front and back injection ports. I have a 6890N with front and back FID that we run a lot of samples on so this isn't a new method development. +…
Hello!
Hoping that everyone is very well, I wanted to know if they can help me, from one day to the next the software stopped responding and asked me in the first instance for a user and password. Letting the software in and just letting a single sample…
What was the EM Voltage before the source cleaning and filament replacement? How old is the electron multiplier? They do not typically fail, the tune EMV setting slowly gets higher and higher. They typically work fine up to ~2500V or so and then the gain…
The Digest of upcoming webinars has been updated as of November 1.
Notable additions include:
Chromatography and Mass Spec (1)
Dissolution Discussion Group (4)
LC & LCMS (2)
Check Out:
Elemental Analysis of Lithium-ion Battery Samples…
Hello! I realize this is an old post but wanted to provide more details in case other users encounter the "Make directory failed" error in the future.
This is captured in Software Status Bulletins (SSB's) in a few places.
The solution, if you encounter…
Hello, I am looking at flavor compounds on a GC/FID. All of my peaks integrate really well except the aldehydes. There is a slight baseline rise long before the actual peak somes out and the GC begins integration at that time. I've tried changing the…
Yes, the peaks are changed at every time in response, and may be a little shifted in retention time, but Ii tried to make autotune , but it failed , so Any suggestions
Hello
I recommend to replace X-belt.
P/N 5410047500 Belt timing – 880 mm
When initializing if the belt tension is not enough, It could be failed.
Please check it.
Hi emilymorin ,
I'm glad you found a solution that works for your data sets. I have continued to investigate this issue, but your solution does not work for all of the data sets I have tested with. I suspect disabling the save file feature may work…
Hello, I am having troubles with the MS40+ pump I use for my ICP-MS machine. I did an oil change yesterday and cleaned out the inside as well as the filters (the oil was pretty low since I had forgotten to check it for a while) and now when I go to turn…
This Information Applies To: Agilent MassHunter 11 and later
Issue
Generating Acquisition Desktop and Quantitative Analysis shortcuts.
Steps to Follow
Double-click the Control Panel icon on the desktop or select Windows Start menu > Agilent...
This Information Applies To: Agilent MassHunter Workstation for LC/TQ and MassHunter Workstation for LC/TOF and LC/Q-TOF
Issue
How to view the MassHunter Data Acquisition Software Logs entries, change settings, and export the Logbook for archiving...
This Information Applies To: ICP-MS MassHunter with User Access Control (UAC)
Issue
It is necessary to update the database folder path in Change User Access Control:
After creating a new database in SDA with ICP-MS MassHunter.
To view a batch...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
Over time, the electrodes may become pitted or eroded and users may see a decrease in precision or begin to experience the "Tube fault" error when new tubes are installed. If...
This Information Applies To: Agilent GTA Furnace and Flame Instruments, Agilent 240FS/240GFAA/GTA120/PSD120
Issue
There may be occasions when users need to remove GTA furnace center block workhead (instruments with both Flame and Furnace capabilities...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
The shroud should be replaced annually, or when there is evidence of damage caused by mechanical shock or contamination from liquid spillage.
Items Required
Shroud Removal...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
Before replacing the electrodes and/or shroud, the GTA Furnace workhead will need to be disassembled. After replacing the electrodes and shroud, the GTA Furnace workhead will...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer
Issue
After starting a run, the run is aborted with the following error: Current = 0.0uA, Expected range: 5 - 3000.
Steps to Follow
Check...
This Information Applies To: Agilent OpenLab CDS 2.x in file system configuration
Issue
Sometimes, you will need to change the Projects Root Path / Project Storage Path . This article outlines the procedure on how to change it.
Background
...
This Information Applies To: 5000 series ICP-OES (5100,5110,5800,5900), AVS 4/6/7
Issue
Steps to bypass the AVS to troubleshoot poor performance on the ICP-OES
Tip : These steps should be completed after the Subsystem Communication...