Hi we are now using masshunter quant to process the data of gc/fid obtain by openlab cds and then using gc translator.the multiplier has already been set in the sequence table.and is there a way to obtain it from the masshunter in the batch table.so the…
Hello!! When running HPLC, I am receiving the following warning which prevents my sequences from running: "DAD method download failed for module G4212B:DEAA303287! Use Signal is not allowed to be changed during run." I am receiving this warning when I…
Hi, i want to update the Firmware of an 5975C with the Firmware Update program msupdate.exe of OpenLab to Version 7.02.29. At the moment the version is 5.02.09 and this version doesn’t support the new OpenLab. Unfortunately the update aborts at one point…
Hello,
I had my 6890 Plus GC connected to Chemstation B04.02 through a G1369B LAN card recently. Today I had a warning #103 "Sig 1 buffer full" shown in the GC display, probably because the PC went to saver mode over the past couple of days. I restarted…
Dear all,
we just recently received an upgrade from OpenLab 2.3 to 2.7. We control a Shimadzu with OpenLab. The Shimadzu GC-FID received a new set of drivers during upgrade.
We are now running into problems during calibration of our runs which were…
I'm using the GC6890 with one single column (CP7429). The gas products have to be analyzed by TCD and FID simutaneously. How should I connect the column to TCD and FID? Is it necessary to have a s plitter to split effluent from a single column to TCD…
Hello scientists, I need help
I am using an MP-AES 4200, It worked perfectly until we had a power interruption. Ever since it has kept giving errors such as
1. Plasma Failed to ignite. This may be due to a low supply of Argon or Nitrogen, a deteriorated…
This Information Applies To: ICP-MS MassHunter with User Access Control (UAC)
Issue
It is necessary to update the database folder path in Change User Access Control:
After creating a new database in SDA with ICP-MS MassHunter.
To view a batch...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
Over time, the electrodes may become pitted or eroded and users may see a decrease in precision or begin to experience the "Tube fault" error when new tubes are installed. If...
This Information Applies To: Agilent GTA Furnace and Flame Instruments, Agilent 240FS/240GFAA/GTA120/PSD120
Issue
There may be occasions when users need to remove GTA furnace center block workhead (instruments with both Flame and Furnace capabilities...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
The shroud should be replaced annually, or when there is evidence of damage caused by mechanical shock or contamination from liquid spillage.
Items Required
Shroud Removal...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
Before replacing the electrodes and/or shroud, the GTA Furnace workhead will need to be disassembled. After replacing the electrodes and shroud, the GTA Furnace workhead will...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer
Issue
After starting a run, the run is aborted with the following error: Current = 0.0uA, Expected range: 5 - 3000.
Steps to Follow
Check...
This Information Applies To: Agilent OpenLab CDS 2.x in file system configuration
Issue
Sometimes, you will need to change the Projects Root Path / Project Storage Path . This article outlines the procedure on how to change it.
Background
...
This Information Applies To: 5000 series ICP-OES (5100,5110,5800,5900), AVS 4/6/7
Issue
Steps to bypass the AVS to troubleshoot poor performance on the ICP-OES
Tip : These steps should be completed after the Subsystem Communication...
This Information Applies To: Agilent 8890/8860 GC Systems with SSL, MMI, PTV, or VI inlets.
Issue
Split vent trap replacement is recommended as part of the scheduled preventive maintenance. Sometimes, it has to be replaced when the inlet pressure...
This Information Applies To: Agilent 6000 Series LC/MS systems equipped with MS40+ rotary vane pumps
Issue
Instructions on how to replace the filter in an Agilent MS 40+ pump as part of annual pump maintenance
Background
The filter in the...