Hello,
What version of the software do you have? The version will be something like CDS 2.x where x is the version change. I would guess that you still have injections setup as cal stds and when you reprocess it is clearing and recreating the calibration…
Hello mass_defect ,
There is currently not a workflow for changing the sample name information in MassHunter after the data file has been acquired. There have been enhancement requests made for this feature but there is currently no timeline for when…
Support and educational resources for the Labware MiniHub
Automation Solutions Knowledge Base
Microplate-Handling Device Guides
PDF user guides
Online Labware MiniHub User Guide
Opening Labware MiniHub Diagnostics
Creating Labware MiniHub…
To enable the Net.TCP Port Sharing Service using MMC
From the Start menu, open the Services Management Console either by opening a Command Prompt window and typing services.msc or by opening Run and typing services.msc into the Open box.
In…
This video guides you through the process of removing the capillary on a system with a VacShield and applies to G6470B, G6475A, G6495C, G6495D, Ultivo (G6465A, G6465B) iQ (G6160A), and Revident (G6575A).
This video is intended to support the written…
This video guides you through the process of installing and removing a capillary with a gate valve and applies to G6495B, G6546A, and 6545XT AdvanceBio (G6549A).
This video is intended to support the written instructions found in the online help or…
New FID Jet!
The latest FID jet is intended for use in 6890/7890/8890/8860/8850/9000 GC models
The legacy jets will not work in the 8890/8850/8860/9000 GC models
The new jet makes installing the column seamless with a conical shape to direct the…
This Information Applies To: Agilent 5975 and 5977 series GC/MSD
Issue:
Tuning the Agilent GC/MSD with EI sources, requires the use of perfluorotributylamine (PFTBA). The calibration vial will be depleted eventually due to regular use. This article...
This Information Applies To: Agilent 5975 and 5977 series GC/MSD
Issue:
If the PFDTD signal is absent or low, but the reagent ions are normal, you may have run out of CI Calibrant.
Inspect the calibration vial on the back of the flow controller...
This Information Applies To: Agilent 5975 and 5977 Series GC/MSD
Issue:
For some GC/MSD maintenance or repair asks, it is required to open the side plate (filament exchange, ion source cleaning, electron multiplier exchange, column installation...
This Information Applies To: Agilent GC/MS MassHunter Acquisition Software Agilent 5975/5977 GC/MSD
Issue
Use the Early Maintenance Feedback (EMF) tool to track the GC/MSD's consumable resource and part use, and to configure alerts for when they...
This Information Applies To: Agilent GC/MSD systems
Issue:
After a filament fails, there will be a system error message: "No emission current". Switching to the other filament (except for the CI ion source, which has just one filament), and then...
This Information Applies To: Agilent 7693A automatic liquid sampler tray
Issue:
The orange Align Mode light comes on . T he sample tray of the Agilent automatic liquid sampler 7693A will not operate again until the alignment procedure has successfully...
This Information Applies To: Agilent 7693A Automatic Liquid Sampler
Issue:
The automatic liquid sampler may need to be replaced, in case it is worn or dirty.
Steps to follow
To remove the syringe:
Open the injector door.
Slide...
This Information Applies To: Agilent 7693A Automatic Liquid Sampler
Issue:
Two turrets are provided with the 7693A injector, the 16-sample standalone turret, and the 3-sample transfer turret used with the 150-sample tray (See Figure 1 ). The turret...
This Information Applies To: Agilent 7697A Headspace Sampler
Issue:
There is a potential leak external to the Headspace unit that can cause loss of pressure.
Steps to Follow:
This article is a troubleshooting guide for when you suspect there...
This Information Applies To: Agilent 7693A Automatic Liquid Sampler
Issue:
This document explains how to replace the syringe carrier assembly in case you want to change from standard to high volume syringes, or if an Agilent support representative...