Thank you for your response. I really appreciate your help. I realized I didn't provide clear information about the experimental conditions. Here are the specific conditions:
Inlet temperature: 250°C
Column oven temperature: 150°C (isothermal) …
Dear All,
We are using NGA analyser as per GPA 2286 method using FID and TCD.
Could you please advice how to apply the bridging to correct the concentration from FID.
Hi again Raina,
as I already told you this cannot be done with just one column, especially with the CO2 concentration up to 20% and water included and the necessity to analyze H2. This is an application we normally build an analyzer for. You need at…
Hello taub .
I think it's a corner case issue and you need a support visit from agilent authorized engineer so please request a service visit as its seems that the error is hidden and not straight forward as you mentioned that you changed alot of things…
Hi guys, when I tried to run my sequence in GC-FID, the workstation showed "front injectors not detected", and under my method, the configuration showed no injectors. However, the parameters I entered for injection could be found in the GC (7890A) operation…
Hi Abdul,
From the picture, it appears your FID flame was extinguished. You can put a metal wrench or a mirror at the top of the detector to see if the exhaust contains moisture from the combustion, but a flat baseline at zero output usually means the…
This instrument is used mostly for FID analyses and the second injector is not working. That's the primary reason why the column will be disconnected most of the time. Also to reduce contamination of the ECD, but it sounds like that isn't a huge concern…
Good Day.
I have an issue to my result in tcd. My Sample is TOGA using Fid and tcd. now the issue is the detection of H2, N2 and O2 are late. before 4.2 min. now its 6.2. the column is new.
We need to use air generator for 8 GCs with FID Detector. Each FID uses 350 mL/min air. So for 8 FID, 2.8L air will be sufficient? Is it ok to go for an air generator that supply 3L of air/min or we need to go for a higher option? Kindly advise
Hi
I am trying to install the G7201D version of ICP MassHunter on a 1909 Windows 10 laptop.
It goes through the initial process and then errors with a code of 0xe0434352.
Some additional research implies this is a .Net error but a repair install…
This Information Applies To: 5200/5300/5400 Fragment Analyzer, Femto Pulse, Oligo Pro II, and ZAG
Issue:
Only plasticware from the approved consumables list should be used in the Agilent Parallel Capillary Electrophoresis systems. The use of plasticware...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Question:
Can more than one Agilent 2100 Bioanalyzer instrument be connected to one PC?
Steps to follow:
It is possible to connect a maximum of two Bioanalyzers to one laptop...
This Information Applies To: 2100 Bioanalyzer, Bioanalyzer Chip Priming Station: part number 5065–4401
Maintenance procedures and how frequently they are required :
Procedure
Time interval
Or if this issue occurs
Where to find a detailed...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue:
Running the hardware diagnostics on the Agilent 2100 Bioanalyzer system can help to investigate whether the instrument performs as expected.
Steps to follow:
Required...
This Information Applies To: 2100 Bioanalyzer, RNA 6000 Nano kit, RNA 6000 Pico kit, Small RNA kit
Issue:
Is it possible to size RNA on the Agilent 2100 Bioanalyzer system?
Resolution:
Agilent offers total and small RNA assays on the Bioanalyzer...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software
Issue:
The Agilent 2100 Bioanalyzer system does not detect a prepared microfluidic chip after it is inserted into the instrument. The interface shows the instrument...
This Information Applies To: 2100 Bioanalyzer, Bioanalyzer chips
Issue:
Can 2100 Bioanalyzer assay chips and reagents be interchanged?
Resolution:
Some assay chips can be used with multiple assays, however some cannot because the chip layout...
This Information Applies To: Agilent MassHunter GC/MS Acquisition software
Issue
The MassHunter software performs several checks during the startup sequence. If it detects a problem, an alert message box will be displayed and the message bar on...
This Information Applies To: Agilent MassHunter Quantitative Data Analysis Software
Issue:
The "NO DATA POINTS" error message appears in the Compound Information window in the lower-left corner in Quantitative Analysis. Sometimes, this problem may...
This Information Applies To: Agilent GC/MSD MassHunter with MSD ChemStation Data Analysis
Issue
When you are using the Data Analysis Report, you may need to specify a certain number of decimal places for your results different to the default decimal...