Good day Agilent, I am really humbled to join the community. I have a few inquiry I would like to make.
I am having a very noisy baseline every time I try to bake out using both ECD and FID,
When I analyze acetaldehyde using the FID it keeps the noise…
Yes, it is off on all gasses, always by roughly 20% (occasionally nearly 30% or as low as 15%, depending on the instrument). Air, Hydrogen, Makeup (N2), carrier (H2 or He) on every instrument (12 GC and 3 GC/MS, which haven't been evaluated). It's also…
Hi.
So ive had a very high sample with Methanol (around 8000 mg/l) and now i still have contamination around 500 mg/l in my blanks. Ive tried injecting IPA and replaced the syringe. Any other tips? Ive also pumped up the oven/column tempature to a…
Canadian_Chemist ,
There is an example of printing text instead of the final concentration based on the LOQ outlier in this discussion.
(+) Report builder - Final Concentration Expression Change - Forum - Mass Spectrometry Software - Agilent Community…
5 psi inlet pressure running hydrogen with your configuration leads to 2.3 ml/min to the MS and 1.02 ml/min to the FID.
You are welcome. Are you using a two-hole ferrule in the injection port or a splitter of some type? The two-holed ferrules are..…
Hello,
3-way valve is a good idea, but unfortunately all I had was several 5180-4160 Tee, 1/8 in, brass, and several 0100-2144 Ball valve, 1/8 inch.
So I decided to make following setup.
In the setup below I am using He as carrier gas and N2 as…
When trying to close a connection on an instrument with an active single run or sequence the OpenLAB CDS software will usually give a message that it will close connection when the runs are finished. Today when trying to close 2 instruments on the same…
Hi all
Apparently the engineer who did the mainboard replacement made a mistake by plugging the MCGV cable to the SSV cable, this made the valve failed to switch (EE 2040.2) and electronic fuse of SSV (EE2049.0) error always appear. It was out of my…
Hi,
My baseline is around 8pA in standby state. H2 is coming from a tank and I can rule out contaminations in the gas source because the gas line is splitted with T piece: one is going to the FID EPC and one is going to the inlet PCM. H2 is the carrier…
This Information Applies To: 5200/5300/5400 Fragment Analyzer, Femto Pulse, Oligo Pro II, and ZAG
Issue:
Only plasticware from the approved consumables list should be used in the Agilent Parallel Capillary Electrophoresis systems. The use of plasticware...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Question:
Can more than one Agilent 2100 Bioanalyzer instrument be connected to one PC?
Steps to follow:
It is possible to connect a maximum of two Bioanalyzers to one laptop...
This Information Applies To: 2100 Bioanalyzer, Bioanalyzer Chip Priming Station: part number 5065–4401
Maintenance procedures and how frequently they are required :
Procedure
Time interval
Or if this issue occurs
Where to find a detailed...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue:
Running the hardware diagnostics on the Agilent 2100 Bioanalyzer system can help to investigate whether the instrument performs as expected.
Steps to follow:
Required...
This Information Applies To: 2100 Bioanalyzer, RNA 6000 Nano kit, RNA 6000 Pico kit, Small RNA kit
Issue:
Is it possible to size RNA on the Agilent 2100 Bioanalyzer system?
Resolution:
Agilent offers total and small RNA assays on the Bioanalyzer...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software
Issue:
The Agilent 2100 Bioanalyzer system does not detect a prepared microfluidic chip after it is inserted into the instrument. The interface shows the instrument...
This Information Applies To: 2100 Bioanalyzer, Bioanalyzer chips
Issue:
Can 2100 Bioanalyzer assay chips and reagents be interchanged?
Resolution:
Some assay chips can be used with multiple assays, however some cannot because the chip layout...
This Information Applies To: Agilent MassHunter GC/MS Acquisition software
Issue
The MassHunter software performs several checks during the startup sequence. If it detects a problem, an alert message box will be displayed and the message bar on...
This Information Applies To: Agilent MassHunter Quantitative Data Analysis Software
Issue:
The "NO DATA POINTS" error message appears in the Compound Information window in the lower-left corner in Quantitative Analysis. Sometimes, this problem may...
This Information Applies To: Agilent GC/MSD MassHunter with MSD ChemStation Data Analysis
Issue
When you are using the Data Analysis Report, you may need to specify a certain number of decimal places for your results different to the default decimal...