Can you prepare the alkane standard in a different alkane, maybe heptane or octane? Boiling point of n-pentane is fairly close to room temperature (36 C) so you may be getting some evaporation of the lighter components in the sample. If there's enough…
Very useful video for basic understanding of the valve functionality. can you post some more videos on GREEN HOUSE GAS ANALYZER or TOGA System in this impressive and easiest way only.
This should take less than one hour. The ion source and quad(s) only need to be below 100° C and the high vacuum pumps - diffusion pump off and cold or the turbo pumps not spinning. Make sure that the GC transferline temperature is set to OFF or 0° C…
The GC inlet must have 20 ml/min or more total flow for good inlet pressure/flow control. If the total flow is too low, air can actually diffuse into the system and the oxygen will damage the column.
Using an Agilent Headspace Sampler the samples are…
Hello ljones031 ,
I would suggest copying the installation files to a folder on the local hard drive and then disconnecting any external drives before attempting installation. Most MassHunter programs will try to install to a D: drive it if is found…
Hello,
If you need the formatting of a table, it can be done that way. I do not like to use multiple hidden tables for that kind of report as they can be hard for later customization. The example below uses a single hidden table and custom code to…
Hello Marty,
thanks for your reply. I tested your hint. It worked and I'm confident to code the formula in the CC.
Thank you very much and have a nice weekend,
Sarah
Hello well ,
I know this is an old forum post, but just wanted to add to what ISH was saying.
The answer still stands, 6890 is not compatible with the 7650 ALS. The GC models it is compatible with are (at the time of this comment at least):
- 8890…
This Information Applies To: 5200/5300/5400 Fragment Analyzer, Femto Pulse, Oligo Pro II, and ZAG
Issue:
Only plasticware from the approved consumables list should be used in the Agilent Parallel Capillary Electrophoresis systems. The use of plasticware...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Question:
Can more than one Agilent 2100 Bioanalyzer instrument be connected to one PC?
Steps to follow:
It is possible to connect a maximum of two Bioanalyzers to one laptop...
This Information Applies To: 2100 Bioanalyzer, Bioanalyzer Chip Priming Station: part number 5065–4401
Maintenance procedures and how frequently they are required :
Procedure
Time interval
Or if this issue occurs
Where to find a detailed...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue:
Running the hardware diagnostics on the Agilent 2100 Bioanalyzer system can help to investigate whether the instrument performs as expected.
Steps to follow:
Required...
This Information Applies To: 2100 Bioanalyzer, RNA 6000 Nano kit, RNA 6000 Pico kit, Small RNA kit
Issue:
Is it possible to size RNA on the Agilent 2100 Bioanalyzer system?
Resolution:
Agilent offers total and small RNA assays on the Bioanalyzer...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software
Issue:
The Agilent 2100 Bioanalyzer system does not detect a prepared microfluidic chip after it is inserted into the instrument. The interface shows the instrument...
This Information Applies To: 2100 Bioanalyzer, Bioanalyzer chips
Issue:
Can 2100 Bioanalyzer assay chips and reagents be interchanged?
Resolution:
Some assay chips can be used with multiple assays, however some cannot because the chip layout...
This Information Applies To: Agilent MassHunter GC/MS Acquisition software
Issue
The MassHunter software performs several checks during the startup sequence. If it detects a problem, an alert message box will be displayed and the message bar on...
This Information Applies To: Agilent MassHunter Quantitative Data Analysis Software
Issue:
The "NO DATA POINTS" error message appears in the Compound Information window in the lower-left corner in Quantitative Analysis. Sometimes, this problem may...
This Information Applies To: Agilent GC/MSD MassHunter with MSD ChemStation Data Analysis
Issue
When you are using the Data Analysis Report, you may need to specify a certain number of decimal places for your results different to the default decimal...