Varian 710 oes, nebulization is ok, fog in the chamber is omogeneous, tubing, nebulizer, torch, cone cleaned and alligned.
Work fine till 2 weeks ago, after i've experienced this: fail to execute wavelenght calibration end torch allign, No response…
Hello Everyone,
I am using 7820A GC coupled with 5977B Mass Spec. After use I close the He tank and later on I get 2 messages - 'Front inlet flow shutdown' and 'Front inlet pressure shutdown'. I restarted the software but it fails to load any GC method…
I am using OpenLab Chemstation C.01.10 on an 8890 with dual FIDs. I was trained on HP's version of Chemstation that reported both detector quant amounts in one row for precision purposes. It made it 10x easier to review data and confirm sample concentrations…
Hi everyone I have a strange issue to report. We are using a 6890GC with FID and TCD that was upgraded many years ago to give use LAN communication rather than GPIB. It works great even though it is over 20 years old. Just prior to Christmas we installed…
Hi Juliana
Yes, most likely the capacitors and/or the RF Tube. However, you can try to reduce the run power to 1.1Kw in the default ignition table. You may then be able to run for a few weeks with this reduced power level. You will need to reduce the…
Hello, we are setting up a seahorse assay for a immunology master class. We want to measure the glycolytic rate in human PBMCs or purified human CD4 T cells activated vs non activated. We fail to see any difference. Has anyone done this kind of assay…
We have a Duo 2.5 foreline pump that was replaced in June of this year (2023). The previous Duo 2.5 installed had a sudden catastrophic leak, thus the replacement in June. The oil was filled up halfway and I set a marker with tape to monitor the level…
Hi byoo,
Do you get any failed to communicate or any other message when you start up the software? You are correct if the busy light should be constantly flashing. This means you got a successfuk firmware load from the PC from ethernet connection. Can…
no you don't need to disconnect it from the FID, ,
bake the column for enough time usually more than 1 hour according to your column status , you can keep the FID working to monitor the baseline .
..
keep temperature 25 degrees less than the maximum…
I have started using GC-FID (Agilent 8890) since March for the first time. We are trying to measure the methane. I was trying to make a standard surve, so I injected 1000 ppm methane standard at first. Just to let you guys know no samples has been run…
This Information Applies To: Agilent GC Systems with Flame Ionization Detector (FID)
Issue:
The Flame Ionization Detector (FID) jet could become clogged with ferrule material, column bleed, or heavy molecular analytes. The clogged jet will affect...
This Information Applies To: Agilent GC Systems with Split/Splitless (S/SL) inlet
Issue
Different liners are required for different high concentration, split analysis techniques including:
General use liners
Auto inject, general use
Auto...
This Information Applies To: Agilent GC Systems with Split/Splitless (S/SL) inlet
Issue
Different liners are required for different splitless trace analysis techniques including:
General use liners
Pressure, temperature, volume (PTV)
Hot...
This Information Applies To: Agilent 6890, 7890, 7820, 8890 and 8860 GC Systems with Split/Splitless (S/SL) inlet
Issue
Replacement of the Gold Seal is required as part of inlet maintenance. Replacement is required when the performance of the inlet...
This Information Applies To: Agilent GC Systems with Micro-ECD.
Issue
The Wipe Test is an annual test that performed by end user of the micro-ECD (Micro Electron Capture Detector or uECD) to help ensure radioactive safety when using the detector...
This Information Applies To: Agilent GC Systems with thermal conductivity detector (TCD)
Issue
Baking the thermal conductivity detector (TCD) at high temperatures can remove sample contaminants that have deposited on the detector surfaces.
Items...
This Information Applies To: Agilent GC Systems with flame ionization detector (FID)
Issue
Baking out the flame ionization detector at high temperatures can remove sample contaminants that have deposited on the detector surfaces.
Items required...
This Information Applies To: Micro Electron Capture Detector (uECD)
Issue
Baking the micro electron capture detector (µECD) at high temperatures can remove sample contaminants that have deposited on the detector surfaces.
Warning ...
This Information Applies To: Agilent GC Systems with Flame Ionization Detector (FID)
Issue
This article will describe how an operator can configure the makeup gas on both the instrument keypad and the software driver (Method Editor).
Background...
This Information Applies To: Agilent HPLC systems
Issue
The presence of ghost peaks can be a symptom of a system contamination issue, caused by accumulation of sample and/or foreign substances in the flow path. It is critical for high sensitivity...