I am a user of an Agilent 7900 ICP-MS. It has been working fine since last month, but today (Oct 13, 2022) the software was not able to connect to the instrument. When I try to connect the MassHunter software to the ICPMS by going to settings > mainframe…
Thanks for the answer but I still fail to understand.
If helium pressure at the inlet of the TD is constant and only controlled manually, why can't it be controlled by the AUX EPC?
Can't I just connect one of the outlet of the AUX EPC through a t…
We fail to properly communicate with the turbo V70 controller, model 969-9507, using RS232.
The communication is ok for all commands that do not answer with more than two bytes, like start and stop.
However, commands supposed to answer with more than…
We have a GC-MS instrument and it works well. Recently we installed a new column which connected to FID detector. Now we want to run a method with GC-FID/MS. However, we observed the peaks only in MS spectrum without FID spectrum. We need help with the…
Hi Everyone
This is my first post here in this community. And I really hope to get some ideas to fix my problem, since i'm getting slowly desperate!
So here's my problem: We have some really bad contamination/peaks on all our polar Systems:
I…
This document contains a list of FAQ and troubleshooting links for Agilent Cell Analysis products. See also Collection of Cell Analysis Resources .
FAQs
Seahorse:
Agilent Seahorse XF Imaging and Normalization FAQs
Agilent Seahorse XF Real…
Hi community
we getting error message (Configuration system failed to initialize. Chemstation will shutdown now) when we trying to launch Chemstation ,we try rename conf. files in C:\Chem32\1 but that not work.
I appreciated any help .
Dheya
Hi,
I get this Front Inlet: Septum purge Pre shutdown warning with Error code: 20401202 with cause showing EPC module is going into a shutdown. This warning showed up immediately after the maintenance was performed to change the septum and SSL liner…
This file contains a list of 59 commonly used consumables and parts for 7890 GC .
Upload this file to your Smart Alerts software to automatically add these parts to the Master Parts List
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
How to power on the Agilent ICP-MS Foreline Pump when fully powering on the Agilent ICP-MS System, or after performing maintenance.
Background
The ICP...
This Information Applies To: Agilent ICP-MS MassHunter Software version 5.1 and above
Issue
The user manuals for Agilent ICP-MS Systems for MassHunter 5.1 and above are included in the ICP-MS MassHunter Help and Learning Center. There are manuals...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Elevated oxide ratio values are defined as greater than 1.5% for x-lens configuration or greater than 3% for s-lens configuration. Possible causes are contamination...
This Information Applies To: Agilent GC/MS Systems
Issue
The software version is a valuable information usually required for troubleshooting, software updates preparation or to check installed options.
Table of contents
MassHunter GC/MS Acquisition...
This Information Applies To: Agilent LC modules with RFID tag readers
Issue
Agilent uses RFID (radio frequency identification tag) tag readers in some HPLC components such as detector lamps and flow cells, pump heads, purge valve and mixers. However...
This Information Applies To: Agilent LC systems with Lab Advisor software.
Issue
In Lab Advisor, the Logs and Results register is available for gathering history and additional information on the system. It presents data collected from the configured...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
What information does the ICP-MS instrument status indicator provide?
Background
The ICP-MS Instrument Status Indicator on the instrument, and in the...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
How to power off Agilent ICP-MS systems before maintenance, for long-term shutdown, or for power cycling the instrument. Power cycling may be required when...
This Information Applies To: Agilent OpenLab CDS
Issue
Steps to close an instrument connection to a primary instrument controller, to start a successful connection to a secondary instrument controller, or to configure the instrument.
Background...
This Information Applies To: Agilent HES source, Agilent 5977 Series GC/MSD
Issue:
During normal operation of the GC/MSD, the ion source will need to be disassembled to proceed with abrasive ion source cleaning and / or replacement of consumable...