Thank you for the help so far. I was able to solve the problem on my results table by using the "left outer join" function.
However, the report will not print the individual peak chromatograms for the target ion or qualifiers if there was no peak detected…
Hi,
1. It is not normal, that you have to purge the cell gas lines every time
2. Ou should perform at least following "Tests" during Plasma ignition: Torch Axis - EM - Resolution/Axis. But a performance report every day would be nice (and therefore…
Hi everyone I have a strange issue to report. We are using a 6890GC with FID and TCD that was upgraded many years ago to give use LAN communication rather than GPIB. It works great even though it is over 20 years old. Just prior to Christmas we installed…
Varian 710 oes, nebulization is ok, fog in the chamber is omogeneous, tubing, nebulizer, torch, cone cleaned and alligned.
Work fine till 2 weeks ago, after i've experienced this: fail to execute wavelenght calibration end torch allign, No response…
Hello Everyone,
I am using 7820A GC coupled with 5977B Mass Spec. After use I close the He tank and later on I get 2 messages - 'Front inlet flow shutdown' and 'Front inlet pressure shutdown'. I restarted the software but it fails to load any GC method…
I am building a report for some GC-FID data from a GC-MS/FID instrument. I have managed to build a report that contains the chromatogram and the table of peaks. I can scale the X-axis to the scale i need but I have been unable to scale the y-axis to show…
I am using OpenLab Chemstation C.01.10 on an 8890 with dual FIDs. I was trained on HP's version of Chemstation that reported both detector quant amounts in one row for precision purposes. It made it 10x easier to review data and confirm sample concentrations…
Hello, we are setting up a seahorse assay for a immunology master class. We want to measure the glycolytic rate in human PBMCs or purified human CD4 T cells activated vs non activated. We fail to see any difference. Has anyone done this kind of assay…
Hi Juliana
Yes, most likely the capacitors and/or the RF Tube. However, you can try to reduce the run power to 1.1Kw in the default ignition table. You may then be able to run for a few weeks with this reduced power level. You will need to reduce the…
We have a Duo 2.5 foreline pump that was replaced in June of this year (2023). The previous Duo 2.5 installed had a sudden catastrophic leak, thus the replacement in June. The oil was filled up halfway and I set a marker with tape to monitor the level…
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
How to power on the Agilent ICP-MS Foreline Pump when fully powering on the Agilent ICP-MS System, or after performing maintenance.
Background
The ICP...
This Information Applies To: Agilent ICP-MS MassHunter Software version 5.1 and above
Issue
The user manuals for Agilent ICP-MS Systems for MassHunter 5.1 and above are included in the ICP-MS MassHunter Help and Learning Center. There are manuals...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Elevated oxide ratio values are defined as greater than 1.5% for x-lens configuration or greater than 3% for s-lens configuration. Possible causes are contamination...
This Information Applies To: Agilent GC/MS Systems
Issue
The software version is a valuable information usually required for troubleshooting, software updates preparation or to check installed options.
Table of contents
MassHunter GC/MS Acquisition...
This Information Applies To: Agilent LC modules with RFID tag readers
Issue
Agilent uses RFID (radio frequency identification tag) tag readers in some HPLC components such as detector lamps and flow cells, pump heads, purge valve and mixers. However...
This Information Applies To: Agilent LC systems with Lab Advisor software.
Issue
In Lab Advisor, the Logs and Results register is available for gathering history and additional information on the system. It presents data collected from the configured...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
What information does the ICP-MS instrument status indicator provide?
Background
The ICP-MS Instrument Status Indicator on the instrument, and in the...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
How to power off Agilent ICP-MS systems before maintenance, for long-term shutdown, or for power cycling the instrument. Power cycling may be required when...
This Information Applies To: Agilent OpenLab CDS
Issue
Steps to close an instrument connection to a primary instrument controller, to start a successful connection to a secondary instrument controller, or to configure the instrument.
Background...
This Information Applies To: Agilent HES source, Agilent 5977 Series GC/MSD
Issue:
During normal operation of the GC/MSD, the ion source will need to be disassembled to proceed with abrasive ion source cleaning and / or replacement of consumable...