Here is the contact information for Agilent in Brazil. https://www.agilent.com/sites/agilent/en/contact-us/brazil
The Agilent Salesperson in Brazil is Marcelo Azevedo - marcelo.azevedo@agilent.com
Hello LC92 ,
Did you run the installer as an Administrator? That might cause issues like this.
Another thing to try is running the Software Verification Tool found in the Start menu under Agilent Technologies. See if there are any missing files. You…
Learn about how to check and extend the lifetime of peristaltic pump tubing; prevent and remove nebulizer blockages; clean the nebulizer and improve precision and reduce memory effects with spray chamber cleaning.
Preventative maintenance is crucial…
Learn more about accurate ICP-MS standard preparation, sample introduction, diagnosis of sample introduction issues, and preventive ICP-MS maintenance guidelines. In this video we provide simple steps to improve sensitivity and accuracy, precision, and…
If you have data associated with a worksheet you cannot make modifications to it. Depending on your software version, you will need to either do "Save As" and give it another name, or create a new worksheet from template. Then the new worksheet will not…
Hello. You have to adjust Nitrogen pressure to get the blue bar inside green area. Pressure regulator is located on the right side of the 4107. It should be ~ 600kPa.
Hello mipastor,
Thank you for your response. I think we do have problem with the MS2 heater. Agilent customer support hinted that it might be sensor problem or the board so service engineer will have to take a look.
The Digest of upcoming webinars has been updated as of April 23.
The new Agilent Community Group, GPC/SEC Solutions Group is hosting a webinar series in partnership with Dow in April: A Journey through SEC, Light Scattering, and 2D-LC for Macromolecules…
This Information Applies To: 5200, 5300 and 5400 Fragment Analyzer, Femto Pulse and ZAG DNA analyzer
Issue
When no data is available in the Agilent ProSize data analysis software for one or more capillaries, the capillary(ies) could be misaligned...
This Information Applies To: Agilent ICP-MS (7800/7850/7900/8900)
Issue
How to check the MS40+ or MS40-S foreline pump to determine if the pump needs maintenance?
Background
The oil's cleanliness and level, in the MS40+ or MS40-S foreline...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Powering on Agilent ICP-MS Systems after maintenance, long-term shutdown, or for power cycling.
Steps to Follow
Confirm that the ICP-MS power plug...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
How to power on the Agilent ICP-MS Foreline Pump when fully powering on the Agilent ICP-MS System, or after performing maintenance.
Background
The ICP...
This Information Applies To: Agilent ICP-MS MassHunter Software version 5.1 and above
Issue
The user manuals for Agilent ICP-MS Systems for MassHunter 5.1 and above are included in the ICP-MS MassHunter Help and Learning Center. There are manuals...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Elevated oxide ratio values are defined as greater than 1.5% for x-lens configuration or greater than 3% for s-lens configuration. Possible causes are contamination...
This Information Applies To: Agilent GC/MS Systems
Issue
The software version is a valuable information usually required for troubleshooting, software updates preparation or to check installed options.
Table of contents
MassHunter GC/MS Acquisition...
This Information Applies To: Agilent LC modules with RFID tag readers
Issue
Agilent uses RFID (radio frequency identification tag) tag readers in some HPLC components such as detector lamps and flow cells, pump heads, purge valve and mixers. However...
This Information Applies To: Agilent LC systems with Lab Advisor software.
Issue
In Lab Advisor, the Logs and Results register is available for gathering history and additional information on the system. It presents data collected from the configured...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
What information does the ICP-MS instrument status indicator provide?
Background
The ICP-MS Instrument Status Indicator on the instrument, and in the...