Dear Community
I am using a GC/FID from Agilent with Openlab CDS. The GC/FID has to columns (front and back) which gives a slightly different retention time for the same substance. I use both lines, one for the measurement and the other for the control…
I don't think it would have a problem as long as you're not trying to connect with both software platforms at the same time. I've seen other customers do similar things (GCMS/FID, using MSD Chemstation for MSD work and GC Chemstation for FID work).
Are there electronic checks that can check to make sure a filament isn't failing because of an electronic issue? We had a filament die, which isn't too surprising considering it was nearly ten years old (teaching institution, the instrument sees periodic…
Hello,
For awhile now, I've been having issues with my resolution axis "passing" for masses 25 and 26 in no gas mode. I have done many cleanings and new tuning solutions. Can anyone explain what is causing this continual failing and what I could do…
Hello Agilent community,
I have recently been 'Recovery Test in GMP' of Openlab 3.4 (Build 3.4.0.242) in a standalone environment using the Windows Hyper-V feature.
During the testing, I found the following two issues
First, a warning message…
I work in a small, environmental lab. We test aluminum levels in serum using ICP-MS. We can run batches of 250 samples at a time. We dilute 500 microliters of serum to 5 ml using 0.2% HNO3. We calibrate using 1, 5, 10, and 20 ppb Aluminum std. At the…
Good morning,
We have an Agilent 7820A GC-FID equipped with a G4567A autosampler.
In the middle of a sequence, the system gave the following errors:
ALS Failure State: Preparing Samples
ALS Failure Code 945 : Autoinjector back tower plunger…
Hello, Just to add on to dnprulz 's reply, the expression that he provided will work in OpenLab Custom Calculator and should perform what you are looking to do. However, if you want the pass/fail logic to be set on the report template then you will want…
The Digest of upcoming webinars has been updated as of December 13.
Notable additions include:
Atomic (4)
GC & GCMS (9)
Vacuum Solutions Series (1)
Check Out:
New Year resolution for my ICP-MS: I will keep my ICP-MS analysis free from…
We have OpenLab 2.1 (with content manger) running our GC and LC systems. We have successfully been running 2 x GC and 6 x LC systems however this morning on two of the systems we can see the following error:
Acquisition
Failed to connect to the…
This Information Applies To: Agilent 6000 Series LC/MS systems.
Issue
Checking and adjusting the nebulizer needle is part of regular maintenance or troubleshooting tasks. It is suggested when there is an issue with nebulizer spray shape or spray...
This Information Applies To: Agilent Single Quadrupole LC/MS systems controlled by OpenLab CDS software
Issue
How to check and recognize the current Instrument Status of your 6100 Series and InfinityLab LC/MS systems using OpenLab CDS software....
This Information Applies To: Agilent LC/MS Systems
Issue
Contamination of the tune mix or the Calibrant Delivery System (CDS) of your LC/MS system can cause Autotune failures and drops in sensitivity due to ion suppression.
Items Required...
This Information Applies To: Agilent LC/MS Systems
Issue
When there is suspected contamination of the CDS, low tune response, or possible blockage in the CDS, flushing the Calibrant system may be required.
Warning : This procedure risks...
This Information Applies To: Agilent LC/MS System
Issue
Instructions on how to check the level of calibrant in your LC/MS system, and refill the calibrant bottle if necessary.
Requirements
Checking the level of calibrant should be performed...
This Information Applies To: Agilent 6100 Series LC/MS Instruments
Issue
Instructions on how to fill the calibrant bottle in Agilent 6100 Series LC/MS Instruments when calibrant levels are running low.
Background
The ability to autotune your...
This Information Applies To: Agilent 6000 Series LC/MS systems
Issue
The article details the correct tuning mix to use according to your LC/MS system and the source type installed on your system. In cases where Agilent tuning mixes need to be diluted...
This Information Applies To: Agilent 7693A, 7650A, and 7683 Series automated liquid samplers
Issue
GC software or GC LED display shows ALS Failure code 245: Autosampler front tower plunger error or ALS Failure Code 945: Auto injector back tower...
This Information Applies To: TapeStation ScreenTapes and reagents
Issue
Using the search tool on Agilent.com to locate the declarations of conformity (DOC) for Agilent ScreenTapes and Test-Tapes, certificates of conformity (COC) for TapeStation...
This Information Applies To: Agilent 7693A Automatic Liquid Sampler
Issue:
The Automatic Liquid Sampler (ALS) system calibration process aligns the sample tray with the injector turret position to enable vial transfers without incident.
Calibration...