Hi Brenda, Whats the total flow setting on the inlet set at? If the total flow is set high because of a high split can be one reason. I suspect this is more of a hardware fault like a blocked split line or a split valve problem. Shutdown #4 This message…
Hello Maybe this question be out-of-date for the current time but I will be appreciate for everyone that can help me. I have few Varian CP-3800 GC in our Lab, unfortunately some of them failed to operate because of electrical board part. I requested these…
In our company we are using a GC-FID Agilent technologies 7820A connected to a Headspace 7697A from Agilent also,
and we are not able to transfer some methods into our system when the carrier gas is Nitrogen.
Our team is in charge of the Method transfers…
Dear Team,
Is it OK to use 8860 system for USP467, residual solvents analysis ? Literature that is available is mainly on 8890 but 8860 can also be used ? Agilent do have a blood alcohol analysis app note on 8860 with HS, 1 SSL, a Tee connection, 2…
Hello,
We just recently got a new tapestation 4150 in our lab, which we're trying to set up. As a part of the setup I rand the full system diagnostics to see if the system is working with the Tapestation Test Tape. Everything runs successfully and the…
Hello dexter91, I need to have the column configuration from your system in order to give you a proper answer: are you using only 1 column with a splitter at the end to split it to the MS and the FID or you have 2 columns configured, 1 for each detector…
Hello,
Please mention the instrument you are trying to work with.
Please see the following for GC:
GC Signal Conversion Factors
Use to convert to display scale units
Use to convert to unscaled…
We currently use Agilent 7890A GC with S/SL injector and FID detector using a capillary column for the analysis of crude oil composition upto C35. The remaining compounds will be reported as C36+. The temperature program is from 30 Deg to 325 Deg, We…
Hello, thanks for update (I wonder if my memories were incorrect,,, Your question is classed "difficult" ...... Let me start easier one! The visible lamp is not required replacing. It seems working without error. that is typical "bulb" , if id is out…
Problem: Unable to perform Instrument Configuration for Agilent 1290 LC. The instrument pings at IP address 192.168.254.11 with NO packet loss and connects fine in Agilent Lab Advisor software. Able to perform instrument commands in Lab Advisor.
However…
This Information Applies To: Agilent LC Pumps
Issue
If a user suspects that the gradient composition isn’t accurate and causes poor chromatography such as retention time shifts, late, early, no peaks or merging peaks. This article provides a quick...
This Information Applies To: Agilent 1290 Infinity (G4226A) and Agilent 1260 Infinity (G1367E) HiP Autosampler
Issue
Replacing the Needle Seat of the Autosampler is required when:
The needle seat is visibly damaged.
Leaks or blockages in the...
This Information Applies To: Agilent OpenLab CDS
Issue
This article discusses different types of bracketing modes and how to set up a bracketed calibration in Data Analysis for OpenLab CDS 2.x
Background
Occasionally, the instrument conditions...
This Information Applies To: Agilent OpenLab CDS
Issue
Identifying the baseline codes and baseline code descriptions for OpenLab CDS
Background
OpenLab CDS Data Analysis includes the same integration algorithms as available in both OpenLAB...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to filter a signal in an Intelligent Report.
Requirements
To be able to carry out the procedure as described, the privilege of Data Processing...
This Information Applies To: Agilent OpenLab CDS
Issue
This article outlines different ways to quantify the amount of compound in an unknown sample.
Background
Quantitation uses peak area or height to determine the amount of a compound in...
This Information Applies To: Agilent G1329A/B and G1313A Standard Autosampler
Issue
Replacing the needle seat of the Agilent 1100/1200/1260 Standard Autosampler may be required during regular maintenance, replacing a bent needle, or flow path blockage...
This Information Applies To: Agilent G1329A/B and G1313A Standard Autosampler
Issue
Replacing the needle of the Agilent 1100/1200/1260 Standard Autosampler may be required during regular maintenance, replacing a bent needle, or flow path blockage...
This Information Applies To: Agilent 1290 Infinity (G4226A) and Agilent 1260 Infinity (G1367E) HiP Autosamplers
Issue
Replacing the Needle Assembly of the Autosampler is required when:
The needle is visibly damaged.
Leaks or blockages in the...
This Information Applies To: Agilent 6000 Series LC/MS Systems equipped with MS40+ rotary vane pumps
Issue
Replacing the MS-40+ (rough pump) fluid periodically is a key maintenance procedure to improve vacuum performance and minimize the possibilities...