Hi azrael, The FID is not a pressurized detector so there is no pressure test. You may wish to explore our GC Fundamentals series on our website. See Below for a link Fundamentals of Gas Chromatography (GC) - Part 1 | Agilent Regards James
Hi Mike,
Thanks for the reply but i have run the instrument performance test it was ok.
Customer is using quarts cuvettes.
another issue we found when running wavelength accuracy and precision run from the validation, it missing one or two wavelength…
We have a 7890B that was configured with an MSD but is being reconfigured for a different analysis. It is now running an FID/TCD method, and the aux detector has been disconnected and unconfigured. The MS/Aux Det button on the GC keyboard says no aux…
Hello,
I am having an issue getting the system pressure test to pass. I have referred to the manual and followed all the steps, and have checked for any leaks (there are no visible leaks) and the leak test on the system is also passing - yet the pressure…
Hi This morning the check Tune failed. After adjusting MS1, the tune passed with warnings. Then I decided to autotune. It went through many of the steps until "Enhanced" failed. I am not sure what this step is. Not easy to find any documentation. Can…
When Air gap is 0.2 and the flow rate is 2.1 ml/min then the peak area found 287 by FID but when the air gap is 0 and flow rate is 1.47 ml/min then the area reduced to 141. Where analysis performed by Autosampler.
I think we do this at my lab but not with a valve. We use a plot column and anayze headspace above a water sample. We test for methane ethane ethene and propane useing an FID. The integrated gastight syringe with a valve in it from Fisher helps. We use…
Hello everyone
I have 3 error messages from the Agilent infinity ii 1260 SFC Multi sampler:
1- Metering device Movement Failed ( EE25444.0) 2- Taking needle From park station failed ( EE25105.201 ) 3- Axis did not reach its target position in time…
Using OpenLab EZChrom A.04.1.0.0 with a 6890N GC-FID this error occurs
The IS dept have looked into this and have commented that the systems log mentions that the instance has reached its maximum size of 32MB. We have been running the same system…
Hi, I have the same problem as well. We are using LC 1220 Infinity series. We tried flushing the system with isopropanol for 10 minutes just in case the bubbles are present. However, this does not solve the problem. The pump failed to get ready within…
This Information Applies To: Agilent ICP-MS MassHunter Software 4.x and 5.x
Issue
ICP-MS Instrument Control or Data Analysis Software will not open, or crashes shortly after opening.
Background
MassHunter uses configuration files to store...
This Information Applies To: Agilent ICP-MS MassHunter Software 4.4 and above (Rev C. and Rev D.)
Issue
The Glitch Resetter resets configuration setting files for MassHunter and can be used when the MassHunter software is exhibiting strange behavior...
This Information Applies To: Agilent ICP-MS MassHunter Software 5.x (Rev D)
Issue
It is best practice to note MassHunter Software Settings before running the Glitch Resetter, renaming MassHunter configuration settings files, or before upgrading...
This Information Applies To: Agilent ICP-MS MassHunter Software 4.x (Rev C)
Issue
It is best practice to note MassHunter Software Settings before running the Glitch Resetter, renaming MassHunter configuration settings files, or before upgrading...
This Information Applies To: Agilent ICP-MS MassHunter Software revisions 4.x and 5.x
Issue
How to clear or archive the acquisition queue? How to resolve queue task file errors?
Background
The Acquisition Queue ( Figure 1 ) lists all tasks...
This Information Applies To: Agilent Fluorescence Detectors G1321A, G1321B, G7121A, G7121B
Issue
This article describes how to diagnose a leak in your fluorescence detector (FLD) module.
Steps to Follow
Confirm the leak error originated in...
This Information Applies To: Agilent ICP-MS MassHunter 5.1 Software, SPS 4 Autosampler
Issue
The SPS-4 autosampler (ALS) may need to be reconfigured after the Glitch Resetter tool is used to reset the software or after a change from a different...
This Information Applies To: Agilent G4208A Instant Pilot
Issue
This article describes how to switch the illumination of the autosampler on or off (if available) using the G4208A Instant Pilot.
Items Required
G4208A Instant Pilot for Agilent...
This Information Applies To: Agilent 7683B Automatic Liquid Sampler
Issue:
O nly use this alignment procedure if the injector hardware configuration has changed or if the Align Mode light comes on.
Agilent does not recommend performing this procedure...
This Information Applies To: Agilent MassHunter data acquisition software and MassHunter Quantitative Data Analysis Software
Issue
This article explains the difference between quantifier and qualifier ions and provides some general guidance on quantifier...