Please check your data files and make sure the solvent peak is completely excluded . I have found that some data files I cannot detect ANY analytes of interest in Optimizer, even though I can identify them in standalone Unknowns Analysis. Without fail…
Hi, We observed an error during autotune of QQQ GCMS as "Peak width gain failed", When it was occurred and what is the reason for the repeat error, Autotune was not completed due to " Peak width gain failed".
Please suggest the recommendations and possibility…
jhagel is correct, do not change PE (Yellow) to PTFE (black) seals in round headed pumps (1290 Infinity and Infinity II as well as G7014C). Both seal types have benefits and downsides: While the black seals are generally better when using them with reverse…
Hi Everyone, I'm operating our Cary 3500 and I am helping with an assay being put together based on competitive binding. Because of the competitive binding, the primary and reliable peak *decreases* in size rather than increasing as the concentration…
Hello,
I have a G6545 QTOF / 1260 HPLC system that came with an HP Z440 workstation with Windows 10 as part of the purchase from Agilent. The workstation is ~ 3 years old. The instrument was running normally over the weekend -- when I came back, the…
I have a 5977B MSD that is experiencing a vacuum failure after a scheduled shutdown for renovation work in our facility. Work was completed and now we are restarting the system. At first we though it was the roughing pump, but we have bypassed the remote…
It is great you have such a nice experience with your results, however results accuracy is a matter of hardware robustness and method setting, not software. I your insist on this, I can recommend you to do the following steps:
1- get the licence number…
Im running on an old GCMS with headspace sampler. Its been failing during runs recently. The logbook shows that the oven is not ready at run time for each sample. After about 10 samples it just stops collecting data. The headspace continues to cook all…
Also, please make sure that a default printer is configured in Windows. If no default printer is configured, the following problems may occur: - Printing of a report preview will fail. - the 'Copy To Clipboard' menu will have an error - the 'Custom Report…
Thank you for your question. Unusual high low voltage error is a common instrument and accessory maintenance related and not instrument hardware related issue. Typically, when you see that error, under logbook of your run, you will see chip map. Please…
This Information Applies To: Agilent LC Samplers except dual needle multisamplers
Issue
High pressure in the LC sampler is sometimes due to a clog in the needle seat assembly, the needle, or the sample loop. The needle can pick up sample particulates...
This Information Applies To: All OpenLab CDS ChemStation Edition software-Standalone Workstation
Issue
After launching OpenLab ChemStation Online, the following error is shown: “ChemStation ChemMain has stopped working” . OpenLab ChemStation Online...
This Information Applies To: Agilent AriaMx, Software version 1.8 and later
Issue
The Aria Warm up Feature was introduced with Aria SW/FW 1.8 to reduce baseline drift. The warm-up feature is used to speed up the heating process that would normally...
This Information Applies To: Agilent AriaMx real-time PCR system, AriaMx analysis software
Issue
When a sample name starts with zero, the leading zero disappears from the exported data ( Figure 1 and Figure 2 ).
Background
Removing the leading...
This Information Applies To: Agilent 7890B GC system and 7697A headspace sampler
Issue
The 7697 Headspace Sampler can be configured to communicate directly with the 7890B GC. When this direct communication is configured, the 7697A headspace gets...
This Information Applies To: Agilent GC/MSD systems
Issue:
When performing MS tuning, there is error message "No Emission Current" and tune is aborted.
Steps to Follow
This error normally means that the selected filament is not working. Perform...
This Information Applies To: Agilent OpenLab CDS
Issue
Any desired processing method can be assigned to the current Result Set.
Requirements
A result set available to link the method to.
Correct Privilege (Role Membership) set up for the...
This Information Applies To: Agilent LC and CE Systems compatible with Lab Advisor
Issue:
Firmware is updated or downgraded when new features are added, or to fix some system bugs. It also solves compatibility issues when a new module is added to...
This Information Applies To: Agilent OpenLab CDS
Issue
This article shows how to export a report of peak area and retention time of a sequence in an Excel format.
Prerequisites
To be able to carry out the procedure as described, privileges...
This Information Applies To: Agilent OpenLab CDS
Issue
Reports in OpenLab CDS can be printed or saved manually in Data Analysys, or automatically during reprocessing, or acquisition.
Requirements
The user needs the following Roles and Privileges...