Hi azrael, The FID is not a pressurized detector so there is no pressure test. You may wish to explore our GC Fundamentals series on our website. See Below for a link Fundamentals of Gas Chromatography (GC) - Part 1 | Agilent Regards James
Hi Mike,
Thanks for the reply but i have run the instrument performance test it was ok.
Customer is using quarts cuvettes.
another issue we found when running wavelength accuracy and precision run from the validation, it missing one or two wavelength…
We have a 7890B that was configured with an MSD but is being reconfigured for a different analysis. It is now running an FID/TCD method, and the aux detector has been disconnected and unconfigured. The MS/Aux Det button on the GC keyboard says no aux…
Hello,
I am having an issue getting the system pressure test to pass. I have referred to the manual and followed all the steps, and have checked for any leaks (there are no visible leaks) and the leak test on the system is also passing - yet the pressure…
Hi This morning the check Tune failed. After adjusting MS1, the tune passed with warnings. Then I decided to autotune. It went through many of the steps until "Enhanced" failed. I am not sure what this step is. Not easy to find any documentation. Can…
When Air gap is 0.2 and the flow rate is 2.1 ml/min then the peak area found 287 by FID but when the air gap is 0 and flow rate is 1.47 ml/min then the area reduced to 141. Where analysis performed by Autosampler.
I think we do this at my lab but not with a valve. We use a plot column and anayze headspace above a water sample. We test for methane ethane ethene and propane useing an FID. The integrated gastight syringe with a valve in it from Fisher helps. We use…
Hello everyone
I have 3 error messages from the Agilent infinity ii 1260 SFC Multi sampler:
1- Metering device Movement Failed ( EE25444.0) 2- Taking needle From park station failed ( EE25105.201 ) 3- Axis did not reach its target position in time…
Using OpenLab EZChrom A.04.1.0.0 with a 6890N GC-FID this error occurs
The IS dept have looked into this and have commented that the systems log mentions that the instance has reached its maximum size of 32MB. We have been running the same system…
Hi, I have the same problem as well. We are using LC 1220 Infinity series. We tried flushing the system with isopropanol for 10 minutes just in case the bubbles are present. However, this does not solve the problem. The pump failed to get ready within…
This Information Applies To: Agilent AriaMx real-time PCR system, AriaMx analysis software
Issue
When a sample name starts with zero, the leading zero disappears from the exported data ( Figure 1 and Figure 2 ).
Background
Removing the leading...
This Information Applies To: Agilent 7890B GC system and 7697A headspace sampler
Issue
The 7697 Headspace Sampler can be configured to communicate directly with the 7890B GC. When this direct communication is configured, the 7697A headspace gets...
This Information Applies To: Agilent GC/MSD systems
Issue:
When performing MS tuning, there is error message "No Emission Current" and tune is aborted.
Steps to Follow
This error normally means that the selected filament is not working. Perform...
This Information Applies To: Agilent OpenLab CDS
Issue
Any desired processing method can be assigned to the current Result Set.
Requirements
A result set available to link the method to.
Correct Privilege (Role Membership) set up for the...
This Information Applies To: Agilent LC and CE Systems compatible with Lab Advisor
Issue:
Firmware is updated or downgraded when new features are added, or to fix some system bugs. It also solves compatibility issues when a new module is added to...
This Information Applies To: Agilent OpenLab CDS
Issue
This article shows how to export a report of peak area and retention time of a sequence in an Excel format.
Prerequisites
To be able to carry out the procedure as described, privileges...
This Information Applies To: Agilent OpenLab CDS
Issue
Reports in OpenLab CDS can be printed or saved manually in Data Analysys, or automatically during reprocessing, or acquisition.
Requirements
The user needs the following Roles and Privileges...
This Information Applies To: Agilent 5975 and 5977 Series GC/MSD systems.
Issue
During tuning, MassHunter prompted the error message: "MSD Fault- RFPA Difficulty", and tune action stopped.
Steps to Follow
Try to reconfigure the GC/MS....
This Information Applies To: Agilent OpenLab CSD 2.5 and above
Issue
The integration optimizer helps find a suitable set of integration events. It allows integration parameters to be tuned via sliders (peak width, slope sensitivity, height reject...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue:
This article explains how to install the Agilent 2100 Expert software and connect a PC to an Agilent 2100 Bioanalyzer system.
Steps to follow:
The latest version of...