Thank you very much for your quick attention. I take advice to use Labadvisor, however, the host computer is a windows 7 system and the built-in net framework is NE3.5, but LabAdvisor downloaded from Agilent site needs Net Framework version 4.7.2 , which…
I am new to GC. I am trying to make a calibration table for a set of fatty acid standards using Agilent 8860 (GC-FID)
After the derivitization step, analysis of the resulting methyl esters shows only the solvent peak. Usually a very high solvent peak…
Hi All,
We have a 5977 MSD which came up with two errors following a site power outage:
"Source Heater Error: Timeout - temperature fails to increase under full power." "Analyser Heater Error: Timeout - temperature fails to increase under full power…
Hello,
Does anyone know were the signal data for the live signal displayed in the online signal window is stored and/or how to access it in Chemstation Rev.B.04.03[16]? I would like to write a macro to run in the scheduler to periodically grab a live…
This is absolutely the wrong column. Ammonia and H2S need apolar thick films to be separated and no specialized Free-Fatty-Acid-Phase (FFAP). A CP-Volamines column would do (CP7448) . Ammonia elutes just after CO2 and before water, H2S after water at…
We suddenly lost power during sample injection, when the power back, the autosampler got needle lock fail error message and fail to go back to needle seat, anybody could help? we did a cold start but not work.
First off, it is not the barcode reading that causes the vial leaking, but my best guess is that the barcode reading introduces a variable time, that then can cause a scheduling conflict. This scheduling conflict is then not handled, and the 7697A is…
For the GC-6890 FID detector issues you're experiencing, here's a simplified approach to troubleshoot the errors:
Gas Supplies:
Make sure all gas supplies (utility, makeup, hydrogen) are on.
Check that the pressure…
We have a GC-MA7890B with an FID detector and I are observing spikes in the baseline after we made a couple of changes.
We installed guard columns with unions on inlet and detector side, added a 2nd gas cylinder and required tubing, cleaned the FID…
Thank you for the help so far. I was able to solve the problem on my results table by using the "left outer join" function.
However, the report will not print the individual peak chromatograms for the target ion or qualifiers if there was no peak detected…
This Information Applies To: Agilent AriaMx real-time PCR system, AriaMx analysis software
Issue
When a sample name starts with zero, the leading zero disappears from the exported data ( Figure 1 and Figure 2 ).
Background
Removing the leading...
This Information Applies To: Agilent 7890B GC system and 7697A headspace sampler
Issue
The 7697 Headspace Sampler can be configured to communicate directly with the 7890B GC. When this direct communication is configured, the 7697A headspace gets...
This Information Applies To: Agilent GC/MSD systems
Issue:
When performing MS tuning, there is error message "No Emission Current" and tune is aborted.
Steps to Follow
This error normally means that the selected filament is not working. Perform...
This Information Applies To: Agilent OpenLab CDS
Issue
Any desired processing method can be assigned to the current Result Set.
Requirements
A result set available to link the method to.
Correct Privilege (Role Membership) set up for the...
This Information Applies To: Agilent LC and CE Systems compatible with Lab Advisor
Issue:
Firmware is updated or downgraded when new features are added, or to fix some system bugs. It also solves compatibility issues when a new module is added to...
This Information Applies To: Agilent OpenLab CDS
Issue
This article shows how to export a report of peak area and retention time of a sequence in an Excel format.
Prerequisites
To be able to carry out the procedure as described, privileges...
This Information Applies To: Agilent OpenLab CDS
Issue
Reports in OpenLab CDS can be printed or saved manually in Data Analysys, or automatically during reprocessing, or acquisition.
Requirements
The user needs the following Roles and Privileges...
This Information Applies To: Agilent 5975 and 5977 Series GC/MSD systems.
Issue
During tuning, MassHunter prompted the error message: "MSD Fault- RFPA Difficulty", and tune action stopped.
Steps to Follow
Try to reconfigure the GC/MS....
This Information Applies To: Agilent OpenLab CSD 2.5 and above
Issue
The integration optimizer helps find a suitable set of integration events. It allows integration parameters to be tuned via sliders (peak width, slope sensitivity, height reject...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue:
This article explains how to install the Agilent 2100 Expert software and connect a PC to an Agilent 2100 Bioanalyzer system.
Steps to follow:
The latest version of...