Hello, Does this 6890N have a MSD connected to it, or are you just using 2D detectors on the GC? If you do not have a MSD then the GC/MS drivers should not be causing any issues. Looking over the SV reports you attached, the OpenLab CDS application appears…
Hello CMZainea
unfortunate this problem still hawe
With the help of the user's manual, we already finded several reasons and troubleshoot the error.
They are:
"Check the FID jet for clogs or damage. If the jet is clogged, you can try cleaning…
Hi, I have a GC 6890N with 5973N Mass selective detection, last week the computer failed and I had to change for another computer, on this computer windows XP, I installed the MSD ChemStation G1701EA E.02.00.493 software, on the Agilent MSD configuration…
Methods and Application Resources
Agilent YouTube
Recorded Webinars
Customer Education
CrossLab Method Services
Partner with Agilent CrossLab to accelerate productivity, and design the outcome you want to achieve. Our global team of…
Hello all, I wish if I can find someone help me in this problem in ICP OES 5100 When I have been trying to ignite plasma It's happening one from two actions
1 - Plasma it ignite some moments and after that it turn off and software gives this message…
Hi all,
I have taked the FID from a HP 6890 plus and put it on a Agilent 6890N that had two inlets and two ECD detectors. I only use the front inlet and installed the FID on the front detector, and removed the electronics for the second inlet and…
Even experienced analysts can fail to recognize problems that hamper productivity in the ICP-MS workflow. So we’ve put together tips to help you recognize – and solve – problems in four key areas: sensitivity, accuracy, precision, and background. Replace…
Hello !
The laboratory has a 7890 chromatograph with one evaporator and one FID detector. I want to upgrade it and add a second channel, the same, but for other tasks. I found catalog numbers on the Agilent website, but they are for the 7820 chromatograph…
Hi.
I have GC 8890 with FID detector.
When I turn on the GC, I get this error. I changed the igniter and the cable that is connected from the igniter to the board.
How can I check what is causing this error and how to fix it? There is a suspicion…
Previously there were different length jets depending on whether or not your GC had the adaptable or capillary-only base. (Capillary-only jets are shorter.) These have been replaced with universal FID jets, which will work on both base types going back…
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and platinum shield plate must be installed after performing maintenance, or replacing with new components.
Items Required
Standard...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and shield plate must be removed and inspected during routine maintenance, and when troubleshooting plasma ignition problems. Faults with...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
This procedure tests for an air leak in the sample introduction system, or fault with spray chamber draining, by sealing the end of the torch with a piece...
This Information Applies To: 7700, 7800, 7850, 7900 Agilent ICP-MS instruments
Issue
Error messages related to gas flows can cause the plasma to shut off or disable plasma ignition.
The troubleshooting procedure in this article is applicable for...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Error messages related to water flow or water valve issues can cause the plasma to shut off or disable plasma ignition. While a warning message will still...
This Information Applies To: Agilent Fluorescence Detectors (FLD)
Issue
Sometimes it’s necessary to change FLD EX and EM wavelengths during a run since not all components will excite or emit at the same wavelengths. However, when the wavelength...
This Information Applies To: Agilent Analytical Scale LC Systems
Issue
To troubleshoot high backpressure within an HPLC system, it’s necessary to understand the expected pressure throughout an operating system. The total pressure for an LC is measured...
This Information Applies To: Agilent LC Samplers except dual needle multisamplers
Issue
High pressure in the LC sampler is sometimes due to a clog in the needle seat assembly, the needle, or the sample loop. The needle can pick up sample particulates...
This Information Applies To: All OpenLab CDS ChemStation Edition software-Standalone Workstation
Issue
After launching OpenLab ChemStation Online, the following error is shown: “ChemStation ChemMain has stopped working” . OpenLab ChemStation Online...
This Information Applies To: Agilent AriaMx, Software version 1.8 and later
Issue
The Aria Warm up Feature was introduced with Aria SW/FW 1.8 to reduce baseline drift. The warm-up feature is used to speed up the heating process that would normally...