Problem: Unable to perform Instrument Configuration for Agilent 1290 LC. The instrument pings at IP address 192.168.254.11 with NO packet loss and connects fine in Agilent Lab Advisor software. Able to perform instrument commands in Lab Advisor.
However…
Hello dexter91, I need to have the column configuration from your system in order to give you a proper answer: are you using only 1 column with a splitter at the end to split it to the MS and the FID or you have 2 columns configured, 1 for each detector…
Dear Team,
Is it OK to use 8860 system for USP467, residual solvents analysis ? Literature that is available is mainly on 8890 but 8860 can also be used ? Agilent do have a blood alcohol analysis app note on 8860 with HS, 1 SSL, a Tee connection, 2…
Date and Time: 07/07/2019 07:26 Program: Agilent MassHunter Workstation Software Qualitative Analysis B.03.01 Build Configuration: Release Message: Retrieving the COM class factory for component with CLSID {4CBCEED8-D9F8-4440-A127-4E840D0573DF} failed…
In our company we are using a GC-FID Agilent technologies 7820A connected to a Headspace 7697A from Agilent also,
and we are not able to transfer some methods into our system when the carrier gas is Nitrogen.
Our team is in charge of the Method transfers…
We currently use Agilent 7890A GC with S/SL injector and FID detector using a capillary column for the analysis of crude oil composition upto C35. The remaining compounds will be reported as C36+. The temperature program is from 30 Deg to 325 Deg, We…
I looked around but failed to find anything useful. Is there somehow possible to export results/data from SureMass-deconvolution/ID in Unknowns Analysis for further processing and or statistical analysis (besides .CEF-format)?
Hello, thanks for update (I wonder if my memories were incorrect,,, Your question is classed "difficult" ...... Let me start easier one! The visible lamp is not required replacing. It seems working without error. that is typical "bulb" , if id is out…
Hello,
Please mention the instrument you are trying to work with.
Please see the following for GC:
GC Signal Conversion Factors
Use to convert to display scale units
Use to convert to unscaled…
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and platinum shield plate must be installed after performing maintenance, or replacing with new components.
Items Required
Standard...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and shield plate must be removed and inspected during routine maintenance, and when troubleshooting plasma ignition problems. Faults with...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
This procedure tests for an air leak in the sample introduction system, or fault with spray chamber draining, by sealing the end of the torch with a piece...
This Information Applies To: 7700, 7800, 7850, 7900 Agilent ICP-MS instruments
Issue
Error messages related to gas flows can cause the plasma to shut off or disable plasma ignition.
The troubleshooting procedure in this article is applicable for...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Error messages related to water flow or water valve issues can cause the plasma to shut off or disable plasma ignition. While a warning message will still...
This Information Applies To: Agilent Fluorescence Detectors (FLD)
Issue
Sometimes it’s necessary to change FLD EX and EM wavelengths during a run since not all components will excite or emit at the same wavelengths. However, when the wavelength...
This Information Applies To: Agilent Analytical Scale LC Systems
Issue
To troubleshoot high backpressure within an HPLC system, it’s necessary to understand the expected pressure throughout an operating system. The total pressure for an LC is measured...
This Information Applies To: Agilent LC Samplers except dual needle multisamplers
Issue
High pressure in the LC sampler is sometimes due to a clog in the needle seat assembly, the needle, or the sample loop. The needle can pick up sample particulates...
This Information Applies To: All OpenLab CDS ChemStation Edition software-Standalone Workstation
Issue
After launching OpenLab ChemStation Online, the following error is shown: “ChemStation ChemMain has stopped working” . OpenLab ChemStation Online...
This Information Applies To: Agilent AriaMx, Software version 1.8 and later
Issue
The Aria Warm up Feature was introduced with Aria SW/FW 1.8 to reduce baseline drift. The warm-up feature is used to speed up the heating process that would normally...