Many GC and GCMS installs do not have the items needed to complete the installation. GC and GCMS system installs rely heavily on site readiness and customers having all the material needed, like copper tubing, Swagelok® fittings, and regulators. This…
Additional Items to add to GC and GCMS Orders-Customer Facing.pdf
Did you finally determine the cause of the inconsistent results? I'm having a similar issue with a different instrument. I have gone through my troubleshooting list and failed to identify the issue.
Dear Community
We faced problems with our GC 7890B which is connected to a Leco Pegasus BT. Since this week we have a really high noise, which comes regularly every 5seconds. We already cleaned FID many times, replaced Jet and built the FID out an in…
Hello
We are working on developing a method for detecting mineral oil contamination (MOSH and MOAH) in edible oils. We are able to get MOSH (mineral oil saturated hydrocarbons) to work well, but when we inject a sample for MOAH (mineral oil aromatic…
There are two log files. The main file looks like a lot was going on.
I went back and did a search for "error" and found the following:
Could not create system restore point, error: 0x80070422. Continuing...
Error 0x80096010: Failed authenticode…
No I haven't. But I think that is the only solution. Perhaps there are somehow misalignment making it not robust and the needle fail to go in the vial and abort the run randomly. . I will do the auto-reference and I will wait and see how frequent the…
Hello,
I previously had Quant 11 on my personal computer and decided to upgrade to Quant 12.1. When I tried to use the installer I get an error that "Set up was Interrupted" and fails to install. I tried to go back to Quant 11 but now get the error…
I think our only problem at the moment is a hardware issue (EPC failing to shut makeup gas OFF when called for) that prevents FID ignition… we’re putting in a call for service to resolve that. I’ll be working to resolve user error (Comments Edited by…
We tried all the above steps, but the problem continued. We had to change the parameters in the Methods file as suggested in another reply from Cendy D. to make the instrument continue
Fragment analyser (HS NGS kit) fail to achieve 4µA
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and platinum shield plate must be installed after performing maintenance, or replacing with new components.
Items Required
Standard...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
The torch, bonnet, and shield plate must be removed and inspected during routine maintenance, and when troubleshooting plasma ignition problems. Faults with...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
This procedure tests for an air leak in the sample introduction system, or fault with spray chamber draining, by sealing the end of the torch with a piece...
This Information Applies To: 7700, 7800, 7850, 7900 Agilent ICP-MS instruments
Issue
Error messages related to gas flows can cause the plasma to shut off or disable plasma ignition.
The troubleshooting procedure in this article is applicable for...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Error messages related to water flow or water valve issues can cause the plasma to shut off or disable plasma ignition. While a warning message will still...
This Information Applies To: Agilent Fluorescence Detectors (FLD)
Issue
Sometimes it’s necessary to change FLD EX and EM wavelengths during a run since not all components will excite or emit at the same wavelengths. However, when the wavelength...
This Information Applies To: Agilent Analytical Scale LC Systems
Issue
To troubleshoot high backpressure within an HPLC system, it’s necessary to understand the expected pressure throughout an operating system. The total pressure for an LC is measured...
This Information Applies To: Agilent LC Samplers except dual needle multisamplers
Issue
High pressure in the LC sampler is sometimes due to a clog in the needle seat assembly, the needle, or the sample loop. The needle can pick up sample particulates...
This Information Applies To: All OpenLab CDS ChemStation Edition software-Standalone Workstation
Issue
After launching OpenLab ChemStation Online, the following error is shown: “ChemStation ChemMain has stopped working” . OpenLab ChemStation Online...
This Information Applies To: Agilent AriaMx, Software version 1.8 and later
Issue
The Aria Warm up Feature was introduced with Aria SW/FW 1.8 to reduce baseline drift. The warm-up feature is used to speed up the heating process that would normally...