Hello E_Johnson ,
I’m sorry for the delayed reply to your message.
Thank you for asking this question. Always refer to the applicable Agilent instrument safety information when performing instrument maintenance or repair ( 7890 Series GC Safety Manual…
Hi we are now using masshunter quant to process the data of gc/fid obtain by openlab cds and then using gc translator.the multiplier has already been set in the sequence table.and is there a way to obtain it from the masshunter in the batch table.so the…
Hello!! When running HPLC, I am receiving the following warning which prevents my sequences from running: "DAD method download failed for module G4212B:DEAA303287! Use Signal is not allowed to be changed during run." I am receiving this warning when I…
Hi, i want to update the Firmware of an 5975C with the Firmware Update program msupdate.exe of OpenLab to Version 7.02.29. At the moment the version is 5.02.09 and this version doesn’t support the new OpenLab. Unfortunately the update aborts at one point…
Hello,
I had my 6890 Plus GC connected to Chemstation B04.02 through a G1369B LAN card recently. Today I had a warning #103 "Sig 1 buffer full" shown in the GC display, probably because the PC went to saver mode over the past couple of days. I restarted…
Dear all,
we just recently received an upgrade from OpenLab 2.3 to 2.7. We control a Shimadzu with OpenLab. The Shimadzu GC-FID received a new set of drivers during upgrade.
We are now running into problems during calibration of our runs which were…
Hello scientists, I need help
I am using an MP-AES 4200, It worked perfectly until we had a power interruption. Ever since it has kept giving errors such as
1. Plasma Failed to ignite. This may be due to a low supply of Argon or Nitrogen, a deteriorated…
This Information Applies To: Agilent 6820, 6890, 7820A GC systems with a Split/Splitless (SSL) inlet
Issue
Non-volatile sample matrix components will accumulate in the inlet liner and impact on analytical performance. The inlet liner should be changed...
This Information Applies To: Agilent headspace samplers (HS)
Issue
GC cycle time needs to be calculated correctly. Too short a GC cycle time will reduce sample quality and possibly stop the analysis prematurely. Too long GC cycle time can cause...
This Information Applies To: Agilent 7820A GC
Issue
7820A GC is designed with simplified keypad that comes with five buttons. They are Stop, Prep Run , Start, Up and Down arrow buttons. Changing the IP address requires a different method compared...
This Information Applies To: Agilent Single Needle Autosamplers
Background
Sometimes the user may observe liquid flowing from Port four on the autosampler injection valve. During an injection sequence, it is normal to have liquid from port four...
This Information Applies To: Agilent 4200, 4150, 2200 TapeStation systems
Issue
Can I run an assay using the ladder or sample buffer from a different assay if I have run out of the appropriate assay ladder or sample buffer? Is it possible to run...
This Information Applies To: Agilent ICP-MS 7700, 7800, 7850, 7900, 8800, and 8900 systems
Issue
Peristaltic pump tubing that has lost its elasticity will not deliver the sample to the nebulizer correctly. When the pump tubing appears limp or flattened...
This Information Applies To: Agilent AriaMx real-time PCR system
Issue
AriaMx touch screen displays error code 90 after the Instrument Health Check (IHC), which happens when the AriaMx is switched on, or after running the onboard diagnostic tests...
This Information Applies To: Agilent AriaMx real-time PCR system, AriaMx optical modules
Issue
AriaMx users can change which AriaMx optical modules are installed to upgrade the instrument capabilities or to troubleshoot.
Items Required
Any...
This Information Applies To: AriaMx real-time PCR system
Issue
Error 43 is displayed on the AriaMx touch screen. Error 43 is a voltage error and it normally indicates that the cartridge LED voltage or motor voltage being detected is abnormal. Sometimes...
This Information Applies To: Agilent 2100 Bioanalyzer system
Issue
Can I run qPCR samples containing Sybr® Green I on the Bioanalyzer?
Background
Sybr® Green I is an Intercalating Dye commonly used to detect amplification products in real...