Hello,
This one could be difficult. 2 things come to mind. First make sure you are not saving the folder of the batch into another batch folder. This will void the .b folder and failed to read correctly. Go see if you can into the drive X:Agilent\ICPMS…
Once the lamp got ignited the light arc between anode and cathode has been sustained.
The referring anode voltage typically stabilizes after a certain time and can be heavily influenced by environmental conditions.
Fluctuations in the anode voltage…
Thank you Kbusch.
Is there any videos that can show me how to move needle arm out of the seat. I tried to go through Lab Advisor but the arm does not go to maintenance mode. Lab Advisor timed out and failed to connect to LC. I shut down the sampler…
Hello collrube ,
No such thing as a dumb question
Just so I can understand the question better, do you mean that you used to have a 5890 GC FID system, and you replaced that with an 8890 GC FID system? Or do you mean that your FID on the 5890…
Dear all,
we have not measured many samples, only some organic samples. Could someone please explain, what cause the RF coils change the color like this? Does it affect the plasma ignition? How to clean it properly?
Is it correct, I take the coils…
Hello SimonHarries ,
The only time I have heard an FID trying to re-light itself is when the baseline of the FID dropped below the Lit Offset value.
What is your baseline at (in pA) when the FID is lit, but not running sample? And what is your lit…
Riddle me this. We've encountered a rather strange phenomena when optimising MRM transitions on a Agilent Ultivo TQ. The MS does not have any issues in generating the precursor ion for example 897.5 (216V fragmentor) but fail to generate a product ion…
Hi All,
I am experiencing a configuration issue with a new Thermo Fluorescence Detector installation on a 1200 series LC with OpenLab CDS 2.5. After installing the SII 1.2 Software for the FLD, I try to configure the FLD with Chromeleon, however I am…
May I ask? Did you take an official FLD training? Working on the innards of an FLD usually is for trained staff only. Many things can go wrong here, e.g. replacing the lamp is much different to replacing the lamp on a UV detector. One can screw up the…
Your controller is going in Auto Tune
Autotuning condition is shown when the controller has delivered an output power level higher than a typical value, but the pump is still not reaching full speed value.
It does not matter if it is a normal start…
This Information Applies To: 2100 Bioanalyzer system, 2100 Expert software version B.02.08 or later
Issue
When printing a report to PDF or HTML with the 2100 Expert software, the error "Failed to Generate Report" appears.
Background
This error...
This Information Applies To: 2100 Bioanalyzer system, 2100 Expert software
Issue
Resetting upper or lower markers from their automatically assigned settings in the Agilent 2100 Expert software.
Background
The Agilent 2100 Expert software...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert Software
Issue
Samples with a broad signal such as NGS smears should be analyzed by setting up a region. Analyzing a region is also termed smear analysis.
Steps to Follow...
This Information Applies To: Agilent 2100 Bioanalyzer system, 2100 Expert software without Security Pack addon
Issue
The 2100 Expert software gives a counter mismatch error in the log book which may lead to data loss (blank lanes). Specifically...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software
Issue
The DV 200 score is a quality score for evaluating quality of RNA derived from formalin-fixed paraffin-embedded (FFPE) samples established by Illumina Inc. in 2016. It represents...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software, RIN NA, Error 4501, RNA 6000 Nano kit (p/n 5067–1511 ), RNA 6000 Pico kit (p/n 5067–1513 )
Issue:
The RIN is not displayed in the software or shows as NA. If the RIN is NA, the...
This Information Applies To: 2100 Bioanalyzer, 2100 Expert software, RNA 6000 Nano kit (p/n 5067-1511), RNA 6000 Pico kit (p/n 5067-1513)
Issue:
Which assay should be selected in the Agilent 2100 Expert software when running yeast total RNA samples...
This Information Applies To: 2100 Bioanalyzer system, 2100 Expert software, RNA assay, DNA assay, Protein assay
Issue:
The X-axis description toggle icon in the Agilent 2100 Expert software toolbar ( Figure 1 ) does not change the X-axis from time...
This Information Applies To: 2100 Bioanalyzer systems, 2100 Expert software
Issue: W hen trying to launch the Agilent 2100 Expert software, the process aborts and the user sees run-time error message :
Run-time error '50003 ' often indicates...
This Information Applies To: 2100 Expert software
Issue:
Sometimes the text and images can appear to be the wrong size and in the wrong place in PDF reports generated in Agilent 2100 Expert software (see Figure 1 ).
Figure 1 . Example of wrong...