Hi Everyone,
Due to random readings of my samples, i ran wavelength and photometric accuracy test. Both of them fails, do i need to replace the lamp or is it because of the wavelength drive gear?
thanks.
What likely happened is the wavelength check that is done after lamp ignition failed. When the lamp is switched on, the detector waits 1 minute to warm-up the lamp. Then a check of the deuterium emission line via the reference diode is performed. If the…
When doing autotune I get high precursor in mass 502. I get 12.79% and the limit is 12%. The manual says that it could be contaminated. The equipment has had preventive maintenance recently but it has now this problem. Previously it had a ratio of mass…
If you want to know what specific module is sending a Leak error, this article in the Knowledge Portal can help:
Determining which Module is Causing the Shutdown Error Due to a Leak
The "Valve command failed transport command failed" Error can have…
Anyone have experience with a 7890B causing abnormal signal attenuation and more signal noise than normal? The attenuation problem - the detector's AIB signal has a maximum signal of ~ 69,000 uV however the signal now tops out at ~30,000 uV in the ChemStation…
Hi everybody, firstly, excuse me for my english. Please I need a video about how to install AJS and MMI in qtofms 6545, because we have a tune problem when we use MMI, (tune failed). To autotune the system, we need to remove MMI and install AJS. Any suggestions…
thanks for your answer. Regarding the ion source (EI): it happens that in a relatively new column, the abundance of the peaks of the same control that I had been injecting almost 3 weeks ago, has decreased from 5 x10^5 to almost 1x10^4. I tried injecting…
Hello pathagun ,
First thing you can double check is if any bubbles are present in the solvent lines between the solvent bottles and the degasser or the pump. You can also check if the solvent inlet filters in the bottles are blocked as these can…
The Digest of upcoming webinars has been updated as of January 4.
Notable additions include:
Spectroscopy Digital Workshop & Bootcamp (16)
Check Out:
New Year resolution for my ICP-MS: I will keep my ICP-MS analysis free from contaminants…
Hi Sean...I think I've touched that particular instrument a long time ago. Gary - 50% 28 and 13% 32 after 24 hours is quite a big leak, maybe not massive but certainly needs fixing.
If the system worked fine before it was cooled off for a power fail…
How to Create a New Database in Spectroscopy Database Administrator (SDA)
Multiple Results
This Information Applies To: Spectroscopy Database Administrator (SDA)
Issue
If the old database is full, or after a specific time interval, it is necessary to create a database in SDA. If you receive a message telling you that the database is full...
Update Database Group Path in Spectroscopy Configuration Manager (SCM)
Multiple Results
This Information Applies To: Agilent Spectroscopy Configuration Manager (SCM)
Issue
It is necessary to add a database to a group path in SCM after creating a new database in Spectroscopy Database Administrator (SDA) . If access to an older database...
How to Access Spectroscopy Database Administrator Software (SDA)
Multiple Results
This Information Applies To: Agilent Spectroscopy Database Administrator Software
Issue
The SDA application can only be accessed by a Windows user who is a member of the Windows Administrators group and Windows SDAAdministrators group.
Steps...
This Information Applies To: AriaMx real-time qPCR system
Issue
The instrument fails to reach the required temperature during a run.
Resolution
Check if the temperature of the environment around the instrument is too low resulting in the instrument...
This Information Applies To : Agilent ELSDs G4260A, G4260B, G4261A, G4621B, G7102A, G7102B
Content :
If the evaporator tube of ELSD becomes contaminated with nonvolatile material resulting in poor chromatography, please use the procedure in this...
This Information Applies To: Agilent ICP-MS (7800/7850/7900/8900)
Issue
The oil should be replaced at least once every six months, or when the oil color is indicates it needs to be changed . The foreline pump should be checked monthly. This article...
This Information Applies To: Agilent ICP-MS MassHunter versions 4.4 - 4.6 and 5.x.
Issue
After performing an autotune, the batch tune report will not generate or print.
Background
ICP-MS MassHunter uses an application called ICP-MS Data Analysis...
This Information Applies To: Agilent 6400 Series triple quadrupole LC/MS systems equipped with a gate valve
Issue
Installing the Ion Transfer Capillary after cleaning or replacement in Agilent LC/MS instruments with a gate valve.
Required Items...
This Information Applies To: Agilent OpenLab CDS 2.x
Issue
This article outlines the procedure on how to quantify uncalibrated compounds in OpenLab CDS 2.x. using reference compounds in the processing method compound table.
Background
Uncalibrated...
This Information Applies To: Agilent OpenLab CDS 2.x
Issue
This article outlines the procedure on how to quantify the uncalibrated compounds in OpenLab CDS 2.x when the analytical method requires a fixed response factor.
Background
Uncalibrated...