Dear, Sr
When I want to go to execute any program in WinUV software, it gives a message "Error code 9:1 CSM error,CSM error"
It seems a comunnication error, the instrument is connected via GPIB-USB-HS.
Anyone knows how to do?
I assume it is packed tight with insulation? Otherwise I'd just call Agilent for any ideas, maybe a board is bad or something and you need a service call.
Is there going to be 60 day demos for these products? The previous versions are so buggy that taking a leap of faith and spending more money on these products hoping that there bugs are fixed isn't something that one should be doing. Kevin
Hi. As Chris says, if the flow is 12 ml/min means you have a massive leak.
But, just in case, did you close the Helium cylinder, right? That's a part of the procedure.
Also, I think that 2 years without cleaning the lenses is quite a lot of time…
Hi all,
I was just wondering whether anyone has experienced issues when reducing MS Scan time down from the 500ms default. I am running MS2 scans for method development however whenever I decrease the scan time, the work list does not progress and the…
Hello team
I write this message in order to receive some help regarding the use creation of reports using the Mcrosoft Add-in of a customer's Microlab 5.7. It is supposed that these icons must appear in Microsoft Word in order to create reports but…
Hello,
What version of the software do you have? The version will be something like CDS 2.x where x is the version change. I would guess that you still have injections setup as cal stds and when you reprocess it is clearing and recreating the calibration…
This Information Applies To: Agilent Liquid Chromatography (LC) systems
Issue:
Shutting down the HPLC for a long period requires following this general procedure to prevent damage to the system and the column.
Steps to follow:
Store the...
This Information Applies To: Agilent G7129A/B Autosampler with Sample Thermostat/Cooler G7167-60101 or G7167-60005.
Issue:
The autosampler may stop working from time to time, potentially giving off loud noises and switching off the light. The only...
This Information Applies To: Agilent 5977A/B GC/MSD with EI source, EI Extractor Source, or CI Source.
Issue:
During normal operation of the GC/MSD, the source will require cleaning. It is time to clean the source when:
There is a loss in analyte...
This Information Applies To: Agilent HES source, Agilent 5977 Series GC/MSD
Issue:
During normal operation of the GC/MSD, the source will require cleaning. It is time to clean the source when:
There is a loss in analyte response not improving...
This Information Applies To: Agilent 5977 and 5975 Series GC/MSD systems
Issue
The autotune fails and reports the error Tune action stopped: Gain and offset = 0 and peaks are too narrow!
Resolution
The MSD autotune program is run after routine...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900/8800/8900)
Issue
Condition new or cleaned ICP-MS skimmer cones and sampler cones by aspirating a Conditioning Solution before use.
Background
Drift up can be a sign of...
Turn On the GC/MS Interface and Oven Using OpenLab CDS
Multiple Results
This Information Applies To: Agilent GC/MS instruments controlled by OpenLab CDS software
Issue
Turning on the GC/MS interface heater and Oven using OpenLab CDS software.
Steps to Follow
From the Home tab, click Method > Instrument Setup...
This Information Applies To: Agilent ICP-MS systems (7700/7800/7850/7900)
Issue
The signal monitor function in MassHunter can help with troubleshooting low sensitivity, carry over, contamination, or high background. It can also be used to optimize...
This Information Applies To: Agilent UV detectors (Variable Wavelength Detectors, Multiple Wavelength Detectors, and Diode Array Detectors)
Issue
Checking accumulated hours on the UV lamp.
Steps to Follow
There are four ways to check the accumulated...
This Information Applies To: Agilent 7700/7800/7850/7900/8800/8900 ICP-MS
Issue:
Poor internal standard (ISTD) mixing can cause high relative standard deviation (RSD).
The recommendations in this article are applicable if:
It takes a long...