Hi Tenamyd
Maybe a bit more detail would help to get you an answer. Here's a few questions:
Is the method gradient or isocratic
Do you prepare the mobile phase freshly each day
Is the column maintained at a set temperature using a column oven…
You will need to plot the piston movement as well. The upper plateau is the secondary piston moving. If the spike is at the beginning of the plateau, then it is more likely the Outlet ball valve. If the spike is at the end of the plateau, it is more likely…
Hello,
Sorry for the late reply. Thank you so much, that actually worked perfectly and I can now produce a report template fit for our purpose. Thanks again and I really appreciate the assistance.
This shows where to drill a 2.5" (6.35 cm) hole in the bench to be able to pass the rough pump hose fittings through to be put the rough pump on a shelf below the bench. Information on how to vent the rough pump to a lab exhaust system is also included…
Putting the GCMS rough pump under the bench SQ and TQ 31Jan2024 with DE.pdf
Hi Mike,
I followed your advice but have not been successful getting any of these methods to work. When I try the first method, I get an error message at the bottom of the screen "Syntax Error in cmd/fct EVALUATE" that prevents the data from being exported…
Hello Tom,
Thank you so much for your reply. This is really helpful. I am running MH V4.6. If you could send me the screen captures for this version would be greatly appreciated!
Cheers,
Inês
My Green Lab’s ACT labelling - Accountability, consistency, and transparency
There are many reasons why I like working at Agilent. One of those is Agilent’s progress towards sustainability and ultimately a zero-carbon future. Collaborating with My Green…
The Digest of upcoming webinars has been updated as of January 31.
Check Out:
Part 2: The Mining Lifecycle and Elemental Analysis Workshop Series on February 6
Acceptability and Antioxidant Properties of Vit D and Saskatoon Berry Fortified Rooibos…
Hello,
You can view the completed injections in a sequence in the reprocessing session(offline) of the instrument. If you are talking about viewing the data for the in-progress injection, you will need to take a snapshot. I did not have anything running…
This Information Applies To: Agilent 7890/7820 GC Systems with SSL, MMI, PTV, or VI inlets.
Issue
Split vent trap replacement is recommended as part of the scheduled preventive maintenance. Sometimes, it has to be replaced when the inlet pressure...
This Information Applies To: Agilent LC pumps
Issue:
Stuck or obstructed check valves (Active Inlet Valve (AIV), Passive Inlet Valve (PIV), Outlet Ball Valve (OBV)) can cause issues such as no-flow or no-pressure, moderate to strong drops in pressure...
This Information Applies To: Agilent 1260 Infinity II multisampler, 1290 Infinity II multisampler, 1260 Infinity II SFC multisampler, and 1260 Infinity II bio-Inert multisampler
Issue
The needle bends while moving to the wash port or showing one...
This Information Applies To: Agilent OpenLab CDS 2.x
Issue
This article outlines the step-by-step instruction on how to overlay chromatograms for OpenLab CDS 2.x
Steps to Follow
Load data from result sets or single samples. See Load or add...
This Information Applies To: Agilent Lab Advisor Software, Agilent Multicolumn Thermostat
Issue:
Agilent Lab Advisor is a great tool to diagnose the issue of your HPLC. Running the tests that are relevant to your specific issue in the Service &...
This Information Applies To: Agilent OpenLab CDS (ver 2.x)
Content:
The following procedure shows how to review completed injections in a running sequence in OpenLab CDS (ver 2.x).
Steps to Follow:
Select the sequence from the Run Queue...
This Information Applies To: Agilent Liquid Chromatography (LC) systems
Issue:
Shutting down the HPLC for a long period requires following this general procedure to prevent damage to the system and the column.
Steps to follow:
Store the...
This Information Applies To: Agilent G7129A/B Autosampler with Sample Thermostat/Cooler G7167-60101 or G7167-60005.
Issue:
The autosampler may stop working from time to time, potentially giving off loud noises and switching off the light. The only...
This Information Applies To: Agilent 5977A/B GC/MSD with EI source, EI Extractor Source, or CI Source.
Issue:
During normal operation of the GC/MSD, the source will require cleaning. It is time to clean the source when:
There is a loss in analyte...