Hello,
We have an agilent 6545. Today when we are doing a mass calibration check, the masses of the negative tune ions seems to be shifted (For example 1633.9988 is now showing 1639.2109 and so on for the other ions) and mass calibration check seems…
Hi,
Our QTOF system failed to do a polarity switch from positive to negative. But it works fine at the positive mode. Just wondering if anybody knows the problem. Here is the instrument log record:
Time EventType EventSource Category Description User…
Actually, you have to be sure that it's detector problem or not.
And if still problem persist and after changing lamps intensity test, wavelength test failed again then you have to call to your local agilent support to check electronics and optics etc…
Hi, I am using Agilent 7820A GC-FID with EZChrom Elite v3.3.2. software. After the completion of each sequence, I would like to automatically generate a .text file along .dat file. So far, after the sequence has ended, I process the sequence and then…
As long as you do not see any issues in your measurements, you can keep using the EM, until your new EM has arrived. At some point the Pulse HV will reach ~1800 V and the Analog HV will reach ~ 3300 V (if you are lucky). After that you will have to replace…
Hello, my friend, After checking the logbook on the ChemStation, note that the method did not run due to an error in the G4212B detector indicating: Start Failed (temperature HW). After that, I checked the instrument with the Lab Advisor, and the Logbook…
Hello,
The RI uses a lamp and since it's works on refractive index differences, it doesn't use a wavelength. The RI is what is called a "bulk" detector.
If you are thinking you can replace the lamp, it's part of the optical unit and when it fails…
Good Evening, I realize this is a bizzare question but basically what we have is a Dean Switch GCMS system and we use cut windows to determine when the best time is to switch from column 1 (inlet to switch to 3rd column - vent) to column 2 (inlet column…
Hello team, I wanted to consult the following: an HPLC 1260, I had to reinstall the software. Once I did it, after creating a new method and giving the order to inject, the software turns blue and immediately turns green and does not inject... After checking…
I am trying to quantify ethyl lactate in ethanol 20% (remainder water). When I run multiple injections, the RSD is 6-8% for the ethyl lactate peak. The ethyl lactate standard should be 0.2% v/v. We typically test samples that are 95-100% ethanol and use…
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, and Oligo Pro II systems
Issue
The volume of sample used by Agilent parallel capillary electrophoresis systems during a run.
Resolution
The...
This Information Applies To: Agilent 2100 Expert software, 2100 Expert Security Pack, 2100 Bioanalyzer
Issue
When opening the 2100 Expert software and using the Security Pack, the error message " Start of launcher application failed - The requested...
This Information Applies To: Agilent 6890, 6850, 7890, 8890, 8860, Intuvo 9000 GC systems.
Issue
The exchange of the ignitor in a Flame Photometric Detector (FPD) may be required in the following scenarios:
Preventive or periodic maintenance...
This Information Applies To: Agilent 1290 Infinity Quaternary Pump G4204A, 1290 Infinity II Flexible Pumps G7104A/C, and G7131A/C.
Issue
If the flexible/quaternary pump does not generate flow or build up pressure, it could be due to a stuck inlet...
This Information Applies To: Agilent 5200, 5300 and 5400 Fragment Analyzer systems
Issue
Separation times for the Fragment Analyzer for each array format and kit.
Resolution
Caution : The times in this article are the length of time...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, Oligo Pro II, ProteoAnalyzer systems
Issue
Guidance for installing the Agilent parallel capillary electrophoresis instrument controller and/or...
This Information Applies To: OpenLab CDS (version 2.x) system
Issue:
This article explains how to export OpenLab CDS 2.x data as Archived file.
For copying OpenLab CDS 2.x data to another Projects or another OpenLab CDS systems, you can use data...