Hello, friends! We have installed a new AAS 280FS device. After installation, the device fails Frequency Diagnostic and Power supply Diagnostic tests according to the SVD software. Please advice, what we can do? Thank you.
Hello Kang: Generally, and aging lamp would be the likely cause of this problem. The average life of the 8453 lamp is 1000 hours. Lamp performance and lifetime may also be affected by physical shock while the lamp is hot, igniting the lamp while it's…
We are trying install OpenLab LTS 01.11 Aug 2022 onto our Windows 10 system; however, the System Preparation Tool states that the Check Pending Reboot step fails even after rebooting the computer.
This is a known issue with the software, but there is…
Thanks for your quick response
but i want to put this limits ( for example 90% to 110%) in my CC editor and in my report called the final result (for example 95%) PASSED and (for example 85%) FAILED. So , how can i translate this limits for different…
Hi all,
I work on a 6470A QQQ. The MS was shut down for maintenance, change of oil of the rough pump, source cleaning, AJS ESI needle replacement and capillary replacement were performed.
Rough vac and high vac values are better than before shutting…
We have intention to upgrade existing Chemstation B version to OpenLab Chemstation C.01.10 version for 6890N and 6890A GC both equipped with TPI inlet (from VAR) and FID.
We are not sure if the upgraded OpenLab CDS able to recognise or support TPI inlet…
Thank you for your advice. Unfortunally not only EM test failed but several others as well. we tried to run it last,first, and even not to run it at all
Hello igorvlad
I’m sorry for the delayed reply to your message. Do you still need assistance with this? If you do, please take into consideration the notes below. However, if the issue was resolved, could you please share what the resolution was?…
The GC Calculators and Method Translation Software (MTS) is available for download from Agilent.com . The package includes:
The Vapor Volume Calculator . It can be used to determine the expansion volume of a GC sample solvent at a given inlet temperature…
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, and Oligo Pro II systems
Issue
The volume of sample used by Agilent parallel capillary electrophoresis systems during a run.
Resolution
The...
This Information Applies To: Agilent 2100 Expert software, 2100 Expert Security Pack, 2100 Bioanalyzer
Issue
When opening the 2100 Expert software and using the Security Pack, the error message " Start of launcher application failed - The requested...
This Information Applies To: Agilent 6890, 6850, 7890, 8890, 8860, Intuvo 9000 GC systems.
Issue
The exchange of the ignitor in a Flame Photometric Detector (FPD) may be required in the following scenarios:
Preventive or periodic maintenance...
This Information Applies To: Agilent 1290 Infinity Quaternary Pump G4204A, 1290 Infinity II Flexible Pumps G7104A/C, and G7131A/C.
Issue
If the flexible/quaternary pump does not generate flow or build up pressure, it could be due to a stuck inlet...
This Information Applies To: Agilent 5200, 5300 and 5400 Fragment Analyzer systems
Issue
Separation times for the Fragment Analyzer for each array format and kit.
Resolution
Caution : The times in this article are the length of time...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, Oligo Pro II, ProteoAnalyzer systems
Issue
Guidance for installing the Agilent parallel capillary electrophoresis instrument controller and/or...
This Information Applies To: OpenLab CDS (version 2.x) system
Issue:
This article explains how to export OpenLab CDS 2.x data as Archived file.
For copying OpenLab CDS 2.x data to another Projects or another OpenLab CDS systems, you can use data...