Hello,
That error usually means that the EM grating motor has failed and will need to be replaced. You should call Agilent support for an onsite call.
As for how can you continue working without the FLD. I assume you have other detector(s) on this…
Hello MikeL ,
Just wanted to post what we discussed during your call with the support center so if anyone else sees a similar problem they will have some things to try.
There can be issues with copying and pasting fairly large amounts of information…
Recently, we connected the column (CP7429) to TCD and FID using a Y splitter. However, there is no signal response on both TCD and FID after manually injection of the calibration gas (containing H2, CO, CH4, C2H4, C2H6 in CO2). The carrier gas is Ar.…
Dear Colleagues, apologizing for frequently wondering but I first faced this problem. GC produces a signal without turning on the FID Detector!? Please look at the attached photo. After turning on the detector and then conditioning the column while the…
For many FID methods, 10-20 Hz data rate is sufficient unless you're doing a fast method of some sort. You need enough data points to define the peak correctly and not get any spectral tilt. Typically 15-20 points across the peak is enough.
i had faced this troubleshooting before
it is probably a software problem.
first close masshunter and double click ( remove masshunter process)
open the soft again and try to create another method with same parameters it should work
also try to…
When performing the Eukariote Total RNA test on the same chip we had some samples with very degraded RNA and one sample with what seems like good quality RNA but the software failed to give a RIN value for that sample. Is there a way to still measure…
Hello AGILENT family,
i have a few questions on the analysis of Pb in blood samples.
am failing to get the right concentrations of the QC sample 8ppb instead it’s reading 0.08 ppb and at the same time it’s also showing overange (0.08o) even when my…
I am a user of an Agilent 7900 ICP-MS. It has been working fine since last month, but today (Oct 13, 2022) the software was not able to connect to the instrument. When I try to connect the MassHunter software to the ICPMS by going to settings > mainframe…
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, and Oligo Pro II systems
Issue
The volume of sample used by Agilent parallel capillary electrophoresis systems during a run.
Resolution
The...
This Information Applies To: Agilent 2100 Expert software, 2100 Expert Security Pack, 2100 Bioanalyzer
Issue
When opening the 2100 Expert software and using the Security Pack, the error message " Start of launcher application failed - The requested...
This Information Applies To: Agilent 6890, 6850, 7890, 8890, 8860, Intuvo 9000 GC systems.
Issue
The exchange of the ignitor in a Flame Photometric Detector (FPD) may be required in the following scenarios:
Preventive or periodic maintenance...
This Information Applies To: Agilent 1290 Infinity Quaternary Pump G4204A, 1290 Infinity II Flexible Pumps G7104A/C, and G7131A/C.
Issue
If the flexible/quaternary pump does not generate flow or build up pressure, it could be due to a stuck inlet...
This Information Applies To: Agilent 5200, 5300 and 5400 Fragment Analyzer systems
Issue
Separation times for the Fragment Analyzer for each array format and kit.
Resolution
Caution : The times in this article are the length of time...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, Oligo Pro II, ProteoAnalyzer systems
Issue
Guidance for installing the Agilent parallel capillary electrophoresis instrument controller and/or...
This Information Applies To: OpenLab CDS (version 2.x) system
Issue:
This article explains how to export OpenLab CDS 2.x data as Archived file.
For copying OpenLab CDS 2.x data to another Projects or another OpenLab CDS systems, you can use data...