I'm using a different version than you so this may not be applicable, but it is worth a shot. In the default "Compound Results" table, it filters out missing peaks. You can include this by opening up the table properties, going to the tab labeled "Peak…
The compound used for tuning EI GCMS systems is PFTBA. FC43. Heptacosafluorotributylamine. Tris(nonafluorobutyl)amine. Perfluorotributylamine
Take a look at this application note for some examples: an-pfas-in-air-5994-5289en-agilent.pdf
…
Hello,
If all you need is the Area Ratio of peak to its' IS then the expression below should work,
Marty
Peak_Area / CurrentPeakOrGroup. ISTD . Peak_Area
I have a 7890B GC with a gas sampling valve and I'm looking for the part number for a 6 port rotor that has a 10mm OD. I have not been able to find the number on any of the provided parts list. Thank you for the help.
Hi AnniarysRnD,
Check in your Processing Method>> System Suitability>>Separation performance computation>> Void time (min). In order to calculate column performance parameters, including Peak_CapacityFactor or Capacity factor of k', you need to enter…
I had notice that the air volume is set to 1ul which is the same as the sample volume (I’m assuming is the same as the injected volume). You could try to set the air volume to 0ul and observe if the injection is consistent after this.
Hi Susana,
Thank you for contacting Cell Analysis Technical Support. Unfortunately, the BIoTek part of our team is not yet on the Agilent Community. However, they can be reached at the below options:
Phone Contact: 800-227-9770 (Option 3, option…
Hi Mike, Thank you, yes correct, here is our situation to clarify, we upgraded in order to retire the Win7 OS. We had methods on Agilent UV 8454 ChemStation B.05.02 that managers would create, reviewers would approve, and analyst could use the methods…
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, and Oligo Pro II systems
Issue
The volume of sample used by Agilent parallel capillary electrophoresis systems during a run.
Resolution
The...
This Information Applies To: Agilent 2100 Expert software, 2100 Expert Security Pack, 2100 Bioanalyzer
Issue
When opening the 2100 Expert software and using the Security Pack, the error message " Start of launcher application failed - The requested...
This Information Applies To: Agilent 6890, 6850, 7890, 8890, 8860, Intuvo 9000 GC systems.
Issue
The exchange of the ignitor in a Flame Photometric Detector (FPD) may be required in the following scenarios:
Preventive or periodic maintenance...
This Information Applies To: Agilent 1290 Infinity Quaternary Pump G4204A, 1290 Infinity II Flexible Pumps G7104A/C, and G7131A/C.
Issue
If the flexible/quaternary pump does not generate flow or build up pressure, it could be due to a stuck inlet...
This Information Applies To: Agilent 5200, 5300 and 5400 Fragment Analyzer systems
Issue
Separation times for the Fragment Analyzer for each array format and kit.
Resolution
Caution : The times in this article are the length of time...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, Oligo Pro II, ProteoAnalyzer systems
Issue
Guidance for installing the Agilent parallel capillary electrophoresis instrument controller and/or...
This Information Applies To: OpenLab CDS (version 2.x) system
Issue:
This article explains how to export OpenLab CDS 2.x data as Archived file.
For copying OpenLab CDS 2.x data to another Projects or another OpenLab CDS systems, you can use data...