UV-Vis spectroscopy is a well-established technique in many laboratories. For decades, laboratories have adapted to pain points associated with UV-Vis workflows such as daily instrument warm-up, yearly lamp replacement, and slow and cumbersome temperature…
Timmas You are running 7890A GC/5975 MS/ E.02.02 SP2 ? --- That version of MSD Chemstation was released November 2013 on Windows XP Professionals with SP3. The KBR error/fix you reference is from a document that does not support MSD Chemstation E.02.02…
Thanks Linh and Martin! first of all, it was not enabled in the instrument configuration. After the reconfiguration with intelligent reporting, I can see editing option! Also that course was very useful to me! Thanks a lot both!
I am having a similar issue. First, I replaced a needle seat and then the auto-referencing failed because I failed to recognize that the black sample holders needed to be removed. The needle mechanism seemed forever stuck in the parked position. I was…
Hello,
I am not sure what you did in your test, but it seems the alfresco instance is not running. The simplest issue might be the licensing if you renamed or changed the MAC on the VM guest.
Marty
We have an Agilent 1290 Infinity II with a multisampler and the instrument is connected to a mass spec. Last week while troubleshooting loss in signal, I noticed a leak in the autosampler. I determined that I needed to replace the needle seat. After replacing…
The Digest of upcoming webinars has been updated as of June 17.
Did you miss the GC Live Event? Don't worry, check out the recording here: GC Live is Back in June with the Next Big Little Thing in GC: The New 8850 GC System !
Notable additions include…
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, and Oligo Pro II systems
Issue
The volume of sample used by Agilent parallel capillary electrophoresis systems during a run.
Resolution
The...
This Information Applies To: Agilent 2100 Expert software, 2100 Expert Security Pack, 2100 Bioanalyzer
Issue
When opening the 2100 Expert software and using the Security Pack, the error message " Start of launcher application failed - The requested...
This Information Applies To: Agilent 6890, 6850, 7890, 8890, 8860, Intuvo 9000 GC systems.
Issue
The exchange of the ignitor in a Flame Photometric Detector (FPD) may be required in the following scenarios:
Preventive or periodic maintenance...
This Information Applies To: Agilent 1290 Infinity Quaternary Pump G4204A, 1290 Infinity II Flexible Pumps G7104A/C, and G7131A/C.
Issue
If the flexible/quaternary pump does not generate flow or build up pressure, it could be due to a stuck inlet...
This Information Applies To: Agilent 5200, 5300 and 5400 Fragment Analyzer systems
Issue
Separation times for the Fragment Analyzer for each array format and kit.
Resolution
Caution : The times in this article are the length of time...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, Oligo Pro II, ProteoAnalyzer systems
Issue
Guidance for installing the Agilent parallel capillary electrophoresis instrument controller and/or...
This Information Applies To: OpenLab CDS (version 2.x) system
Issue:
This article explains how to export OpenLab CDS 2.x data as Archived file.
For copying OpenLab CDS 2.x data to another Projects or another OpenLab CDS systems, you can use data...