Thanks for the feedback. I have re-optimized the lamp alignment, but I didn’t get much (if any) improvement. I also made some adjustments to the sample position, which I think helped a little. I think some users have been fiddling with the sample position…
Hi community,
maybe someone has an idea what I could do, before a technician comes over.
During my absence my colleagues told me that our HPLC (1260 Vialsampler, 1260 Inf II Flex pump, TCC, FC-AS, DAD) does show a peak shift of about 3 to 10 minutes…
This is a chromatogram of my high standard, Still haven't gotten to the low. Note that this is actually just one compound injected on the sorbent tube. The compound is methyl methacrylate. The tube is Carbopack B,X. The library identifies the compound…
So just to let everyone know, the SSD on this computer has now already failed. Seems like there was something wrong with the hardware to start with !. Let's hope a new SSD will fix this issue. -Francois
Hello, I apologize for the delay. A lot of times, autostart macro failed errors are caused by corrupt instrument config files. Try resetting the instrument configuration files in the instrument folder (\Chem32\x\, where x is the number of the instrument…
This article is a compilation of Frequently Asked Questions (FAQs) for Agilent's consumable products in the Chemistries and Supplies Division (CSD). FAQ categories include Filaments and Ion Sources , Gas Management, GC Columns , General , Inlets & Liners…
Hello, Is there an update available for the Chemspider library editor script? The script is named DownloadMolfilesFromChemspider.libedit and as the name suggests, downloads the mol files for each library entry from chemspider. The chemspider API appears…
Hello, Since each compound in your processing method would require a different resolution pass/fail threshold, I do not believe you would be able to set this up solely from the column properties on your intelligent report. I approached this by storing…
The Agilent Equipment Qualification Plan (EQP) for OQ is freely available on the Agilent website for potential customers to review. I have attached the standard EQP OQ for GC
Sounds like the Cap EPC module or the EPC Pneumatics board may have failed. Do you have two Cap Inlets? If so. You can swap the two EPC Modules to see if that changes anything. I would lean towards the EPC Module has failed.
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, and Oligo Pro II systems
Issue
The volume of sample used by Agilent parallel capillary electrophoresis systems during a run.
Resolution
The...
This Information Applies To: Agilent 2100 Expert software, 2100 Expert Security Pack, 2100 Bioanalyzer
Issue
When opening the 2100 Expert software and using the Security Pack, the error message " Start of launcher application failed - The requested...
This Information Applies To: Agilent 6890, 6850, 7890, 8890, 8860, Intuvo 9000 GC systems.
Issue
The exchange of the ignitor in a Flame Photometric Detector (FPD) may be required in the following scenarios:
Preventive or periodic maintenance...
This Information Applies To: Agilent 1290 Infinity Quaternary Pump G4204A, 1290 Infinity II Flexible Pumps G7104A/C, and G7131A/C.
Issue
If the flexible/quaternary pump does not generate flow or build up pressure, it could be due to a stuck inlet...
This Information Applies To: Agilent 5200, 5300 and 5400 Fragment Analyzer systems
Issue
Separation times for the Fragment Analyzer for each array format and kit.
Resolution
Caution : The times in this article are the length of time...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, Oligo Pro II, ProteoAnalyzer systems
Issue
Guidance for installing the Agilent parallel capillary electrophoresis instrument controller and/or...
This Information Applies To: OpenLab CDS (version 2.x) system
Issue:
This article explains how to export OpenLab CDS 2.x data as Archived file.
For copying OpenLab CDS 2.x data to another Projects or another OpenLab CDS systems, you can use data...