I went back and installed a no-hole ferrule and get a passing air/water check (I assume this rules out the MS interface), but when installing a column to the MS interface with the other end capped, the air/water check fails.
Otis,
This is the reply from Engineering:
the connection refused error indicates that the A-Plus server is not reachable, this can happen for two reasons:
The server has gone into error, in this case it is possible to launch A-plus from a dos…
Hello, I am looking for some advice on how to troubleshoot a small air leak in a 7010 triple quad. The leak is small enough that using an an air can at several of the check points can't detect a leak. So far I changed the side plate o-rings, vent valve…
Instrument: 7890 GC modified for gas injection with a 10-port valco valve. It's dual SS inlet, dual detector FID/TCD.
I have installed some components into the AUX bracket, two heating components into AUX 1 and AUX 2, and a valve actuator in V1. Valve…
In the ChemStation calibration table you can set Peak Qualifiers when using multiple signals. The ratio of the signals is calculated and compared for each compound. In the classic report this is then used also for peak identification. I tried building…
We are using EZChrom and two separate samples, so as to increase throughput and to limit solvent use. 7890A/7683/7683 ALS with dual FID. Thanks, Charles
I’m having problems with my injector. It will move up and down to the seat with no problem but will throw an error and not move down to a sample vial. Errors “Command from COSY list rejected (EE 4080,3061)” “Needle down failed (EE 4018, 16)” Also if you…
GC Inlet Maintenance
Find links and part numbers to the consumables used in the video here.
GC Septum
Inlet septa are used to maintain a leak-free seal at the GC inlet, even after repeated injections.
If the septum has a dimple, the dimple…
We have been using an Agilent 7890B GC-MS with FID TCD equipped with an autosampler (ALS) for analysing liquid hydrocarbon samples. I would like to analyse gaseous samples of CO, CO2 and H2 in the future. Is it possible to manually inject gas samples…
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, and Oligo Pro II systems
Issue
The volume of sample used by Agilent parallel capillary electrophoresis systems during a run.
Resolution
The...
This Information Applies To: Agilent 2100 Expert software, 2100 Expert Security Pack, 2100 Bioanalyzer
Issue
When opening the 2100 Expert software and using the Security Pack, the error message " Start of launcher application failed - The requested...
This Information Applies To: Agilent 6890, 6850, 7890, 8890, 8860, Intuvo 9000 GC systems.
Issue
The exchange of the ignitor in a Flame Photometric Detector (FPD) may be required in the following scenarios:
Preventive or periodic maintenance...
This Information Applies To: Agilent 1290 Infinity Quaternary Pump G4204A, 1290 Infinity II Flexible Pumps G7104A/C, and G7131A/C.
Issue
If the flexible/quaternary pump does not generate flow or build up pressure, it could be due to a stuck inlet...
This Information Applies To: Agilent 5200, 5300 and 5400 Fragment Analyzer systems
Issue
Separation times for the Fragment Analyzer for each array format and kit.
Resolution
Caution : The times in this article are the length of time...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, Oligo Pro II, ProteoAnalyzer systems
Issue
Guidance for installing the Agilent parallel capillary electrophoresis instrument controller and/or...
This Information Applies To: OpenLab CDS (version 2.x) system
Issue:
This article explains how to export OpenLab CDS 2.x data as Archived file.
For copying OpenLab CDS 2.x data to another Projects or another OpenLab CDS systems, you can use data...