Wondering if anyone has experience detecting acetic acid and formic acid using GC-FID HSS. I am trying to develop a method based on the limits described in USP <467> of 5000 ug/mL of each of the two solvents, but having a hard time seeing any peaks.
Good morning,
We have an autosampler (Agilent G4567A) for our GC-FID (7820A) and the following method for cleaning and injecting samples.
I have noticed that when the syringe pumps 2µL of sample for cleaning, it then pumps quite a large volume of…
hi community we are developing a method on short chain fatty acids in plasma sample, using a DB fatwax UI column on GC-FID. we are using diethyl ether as extraction solvent however our recovery of patient samples are not so good and looking to use Isoproponol…
Hi, I know this is an old thread, but I am having a very similar issue. I am wondering how did you know to replace the interconnect spring rod? How did you know this was the issue, and that it was not instead an issue with the FID board or the electrometer…
Hi,
After a power cut, the batch file I had open on my desktop seems to have become damaged...
On opening the batch, it fails to open... small dialogue pops up >> "failed to open quick scan file. Failed to read binary quick scan file."
Has anyone…
I have a 6890N GC with an MSD and a GC that I am trying to qualify. The MSD works fine but when it comes to the FID the units are showing as mAU and not PA so it will not pass the validation test. Does anyone have any idea on how we can change the units…
We don't know what is in your water samples, but on a CP-Wax 57 CB benzene and isopropanol are eluting very close to ethanol, just in front of it.
You can find examples of applications of alcoholic beverages on Wax 57 (all types) in Scanview ( (+) Software…
Hello mckenzie.stevens ,
Did this error occur when attempting to work with the FID data? I've not seen this exact error, but it is possible to receive similar errors when having a spectrum tool selected and trying to work with non-MS data. If you then…
I have a 6890N GC with dual FID. The back column has a much higher flow rate than the front column. The two columns are identical and the setup for inlet, column and detector are identical. I have also swapped the EPC's between the two detectors. Seems…
Hello. We have a 2- dimension gc/fid/ms 8890/5977C with a masshunter software. Our aim is to quantify molecular markers (e.g. 1,3,5-Tri-tert - Butylbenzene) used in gasoil to trace fraud. For quantitation we use a sim method (Quantification sim 231 and…
This Information Applies To: Agilent ICP Expert software.
Issue
The software version is often asked and is a valuable information: to see if any updates are needed, if certain options are available etc.
Steps to Follow
Launch ICP Expert...
This Information Applies To: Agilent OpenLab CDS
Issue
This article provides step-by-step instructions to calculate peak-to-valley ratio in OpenLab CDS.
Background
The peak-to-valley ratio is calculated to indicate the quality of peak separation...
This Information Applies To: Agilent 6500 Series Q-TOF LC/MS systems, MassHunter Workstation 10.1 or below and MassHunter Workstation 11.0 .
Issue
Fully reset the Q-TOF LC/MS system via a power cycle without venting. For users who experience slow...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, and Oligo Pro II systems
Issue
The volume of sample used by Agilent parallel capillary electrophoresis systems during a run.
Resolution
The...
This Information Applies To: Agilent 2100 Expert software, 2100 Expert Security Pack, 2100 Bioanalyzer
Issue
When opening the 2100 Expert software and using the Security Pack, the error message " Start of launcher application failed - The requested...
This Information Applies To: Agilent 6890, 6850, 7890, 8890, 8860, Intuvo 9000 GC systems.
Issue
The exchange of the ignitor in a Flame Photometric Detector (FPD) may be required in the following scenarios:
Preventive or periodic maintenance...
This Information Applies To: Agilent 1290 Infinity Quaternary Pump G4204A, 1290 Infinity II Flexible Pumps G7104A/C, and G7131A/C.
Issue
If the flexible/quaternary pump does not generate flow or build up pressure, it could be due to a stuck inlet...
This Information Applies To: Agilent 5200, 5300 and 5400 Fragment Analyzer systems
Issue
Separation times for the Fragment Analyzer for each array format and kit.
Resolution
Caution : The times in this article are the length of time...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer, Oligo Pro II, ProteoAnalyzer systems
Issue
Guidance for installing the Agilent parallel capillary electrophoresis instrument controller and/or...
This Information Applies To: OpenLab CDS (version 2.x) system
Issue:
This article explains how to export OpenLab CDS 2.x data as Archived file.
For copying OpenLab CDS 2.x data to another Projects or another OpenLab CDS systems, you can use data...