I am trying to quantify ethyl lactate in ethanol 20% (remainder water). When I run multiple injections, the RSD is 6-8% for the ethyl lactate peak. The ethyl lactate standard should be 0.2% v/v. We typically test samples that are 95-100% ethanol and use…
I went back and installed a no-hole ferrule and get a passing air/water check (I assume this rules out the MS interface), but when installing a column to the MS interface with the other end capped, the air/water check fails.
Otis,
This is the reply from Engineering:
the connection refused error indicates that the A-Plus server is not reachable, this can happen for two reasons:
The server has gone into error, in this case it is possible to launch A-plus from a dos…
Hello, I am looking for some advice on how to troubleshoot a small air leak in a 7010 triple quad. The leak is small enough that using an an air can at several of the check points can't detect a leak. So far I changed the side plate o-rings, vent valve…
Instrument: 7890 GC modified for gas injection with a 10-port valco valve. It's dual SS inlet, dual detector FID/TCD.
I have installed some components into the AUX bracket, two heating components into AUX 1 and AUX 2, and a valve actuator in V1. Valve…
In the ChemStation calibration table you can set Peak Qualifiers when using multiple signals. The ratio of the signals is calculated and compared for each compound. In the classic report this is then used also for peak identification. I tried building…
We are using EZChrom and two separate samples, so as to increase throughput and to limit solvent use. 7890A/7683/7683 ALS with dual FID. Thanks, Charles
I’m having problems with my injector. It will move up and down to the seat with no problem but will throw an error and not move down to a sample vial. Errors “Command from COSY list rejected (EE 4080,3061)” “Needle down failed (EE 4018, 16)” Also if you…
GC Inlet Maintenance
Find links and part numbers to the consumables used in the video here.
GC Septum
Inlet septa are used to maintain a leak-free seal at the GC inlet, even after repeated injections.
If the septum has a dimple, the dimple…
This Information Applies To: Agilent MassHunter 11 and later
Issue
Generating Acquisition Desktop and Quantitative Analysis shortcuts.
Steps to Follow
Double-click the Control Panel icon on the desktop or select Windows Start menu > Agilent...
This Information Applies To: Agilent MassHunter Workstation for LC/TQ and MassHunter Workstation for LC/TOF and LC/Q-TOF
Issue
How to view the MassHunter Data Acquisition Software Logs entries, change settings, and export the Logbook for archiving...
This Information Applies To: ICP-MS MassHunter with User Access Control (UAC)
Issue
It is necessary to update the database folder path in Change User Access Control:
After creating a new database in SDA with ICP-MS MassHunter.
To view a batch...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
Over time, the electrodes may become pitted or eroded and users may see a decrease in precision or begin to experience the "Tube fault" error when new tubes are installed. If...
This Information Applies To: Agilent GTA Furnace and Flame Instruments, Agilent 240FS/240GFAA/GTA120/PSD120
Issue
There may be occasions when users need to remove GTA furnace center block workhead (instruments with both Flame and Furnace capabilities...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
The shroud should be replaced annually, or when there is evidence of damage caused by mechanical shock or contamination from liquid spillage.
Items Required
Shroud Removal...
This Information Applies To: Agilent GTA 120, 240/280 GTA Furnace
Issue
Before replacing the electrodes and/or shroud, the GTA Furnace workhead will need to be disassembled. After replacing the electrodes and shroud, the GTA Furnace workhead will...
This Information Applies To: Agilent 5200/5300/5400 Fragment Analyzer, Femto Pulse, ZAG DNA Analyzer
Issue
After starting a run, the run is aborted with the following error: Current = 0.0uA, Expected range: 5 - 3000.
Steps to Follow
Check...
This Information Applies To: Agilent OpenLab CDS 2.x in file system configuration
Issue
Sometimes, you will need to change the Projects Root Path / Project Storage Path . This article outlines the procedure on how to change it.
Background
...
This Information Applies To: 5000 series ICP-OES (5100,5110,5800,5900), AVS 4/6/7
Issue
Steps to bypass the AVS to troubleshoot poor performance on the ICP-OES
Tip : These steps should be completed after the Subsystem Communication...